Jump to content

alloyboltz


theshee

Recommended Posts

lol well that shouldnt be too hard to make happen... i got a kid on the way and i still got to chroe all my shit and get my plastics done... so im not going to be ready until after the summer more then likely

I am figuring that my triple won't be ready to do anything for atleast a year. I may try and throw a surrogate engine in the chassis just so I can have some fun with it this summer.

 

Having a kid on the way is no excuse. I have a hard enough time babysitting myself, so I think we're even there. :woot:

Link to comment
Share on other sites

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

That's just terrible.............................I am not sure if you are speaking in material generality or you just have no idea what you're talking about. I am not trying to be an ass (though I usually am), but I seriously cannot understand why your are posting what you are. You have to have some wires crossed in your undertanding of the topic somewhere, but I can't see where it is specifically. :confused:

 

Im just saying stainless steel is weaker in general and I would not trust them where stress points will be critical....no matter how well of materials they use. Now how hard is that to understand?

Link to comment
Share on other sites

Here is an alloybolt I took out of my top shock bracket today... Notice part of it is still in the nut.... Pieces of crap!

2007_0415Raptor0005.jpg

Link to comment
Share on other sites

Im just saying stainless steel is weaker in general and I would not trust them where stress points will be critical....no matter how well of materials they use. Now how hard is that to understand?

I'll buy that..........with regards to how hard it was to understand, you may have wanted to leave the grading portion of your comments out because they were either incorrect or misleading in the way thata less informed person might read that and think that all stainless fasteners are soft, there is no such thing as a graded stainless fastener, or simply there is only one type of stainless fastener made. :geek:

Link to comment
Share on other sites

  • 2 weeks later...
Here is an alloybolt I took out of my top shock bracket today... Notice part of it is still in the nut.... Pieces of crap!

2007_0415Raptor0005.jpg

 

That sucks My firend has the old kit (From RUSS) and they do not look like that.

 

I think Stainless is Strong enough for most parts on the banshee including the shock linkage and A-arms, the factory yamaha botls are crap, much worse than the stainless I'm using, Hell I even twisted the heads off the A-arms botls when they galled up inside my stock arms.

 

That is as long as the bolts fit correctly.

 

Yamaha uses Graded Bolts, but the grade is "Shit x 10"

Edited by Justintoxicated
Link to comment
Share on other sites

  • 2 weeks later...
I have already expressed how much I disliked the kit I got from alloyboltz, but i must say that the kits truely suck ass. The engine case bolts wouldnt torque and caused me to have to split the engine cases again because it made a leak and the yamaha bond didnt seal because the fucking bolts wouldnt stay tight. DO NOT buy an alloyboltz kit, they blow!

Hmmmm.....let me guess... Either you sell bolt kits or you are a complete idiot??? Which is it?

Link to comment
Share on other sites

Hmmmm.....let me guess... Either you sell bolt kits or you are a complete idiot??? Which is it?

 

 

Well, first off I dont sell bolt kits, just had horrible luck with a kit that cost more then is should have for the poor quality of the kit. Second, fuck off... When you pay for the site, I will take your opinions seriouisley, but until you have a supporting member beside your name your opinion means nothing to me. Nice first post too... :thumbsup:

Link to comment
Share on other sites

Well, first off I dont sell bolt kits, just had horrible luck with a kit that cost more then is should have for the poor quality of the kit. Second, fuck off... When you pay for the site, I will take your opinions seriouisley, but until you have a supporting member beside your name your opinion means nothing to me. Nice first post too... :thumbsup:

I was thinking that the guy was talking about Justintoxicated's post................. :blink:

 

My bad. I didn't think you were sellign bolts. I actually bought the Fastenerguy kit due to your experience. :thumbsup:

Link to comment
Share on other sites

Well, first off I dont sell bolt kits, just had horrible luck with a kit that cost more then is should have for the poor quality of the kit. Second, fuck off... When you pay for the site, I will take your opinions seriouisley, but until you have a supporting member beside your name your opinion means nothing to me. Nice first post too... :thumbsup:

:sad: :sad: i guess i dont mean much either then

Link to comment
Share on other sites

:sad: :sad: i guess i dont mean much either then

 

 

Nah your opinions count, I wasnt trying to take a shot at everybody who isnt a supporting member. You along with others, are a well respected guys with endless posts of good info. Your not some ass who comes on here with their first post and blasts a supporting member.

Link to comment
Share on other sites

lol i know.. i was just taking a stab at you lol... no pun intended...

 

and im sure he isnt a new member... he just made a second login...

:thumbsup:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...