banshee x Posted August 18, 2005 Report Share Posted August 18, 2005 I tried 6 psi and it held with no fluctuation for 2 hours after about 3 1\2 hours it dropped about a needle width.I have sprayed the entire engine with soapy water and found no leaks even the flywheel side crank seal. Am I in the clear???? Quote Link to comment Share on other sites More sharing options...
FASTOYS Posted August 18, 2005 Report Share Posted August 18, 2005 YES !!!! 6lbs for 6 minutes ! Quote Link to comment Share on other sites More sharing options...
RBD Posted August 18, 2005 Report Share Posted August 18, 2005 Good to go..... Quote Link to comment Share on other sites More sharing options...
banshee x Posted August 18, 2005 Author Report Share Posted August 18, 2005 SWEEEEETTT thanks Quote Link to comment Share on other sites More sharing options...
Holyman Posted August 18, 2005 Report Share Posted August 18, 2005 Post some pics of your leakdown tester equipment. Quote Link to comment Share on other sites More sharing options...
ellison445 Posted August 18, 2005 Report Share Posted August 18, 2005 Word, I would like to see as well Post some pics of your leakdown tester equipment. 406004[/snapback] Quote Link to comment Share on other sites More sharing options...
Machwon Posted August 19, 2005 Report Share Posted August 19, 2005 (edited) My picture is too large to load. e-mail me at rbracing11@msn.com and I'll send you a picture of a kit I build. Or here is a link to my website: http://groups.msn.com/RBRacingTwoStrokePor...hnicalinfo.msnw Edited August 19, 2005 by Machwon Quote Link to comment Share on other sites More sharing options...
Holyman Posted August 19, 2005 Report Share Posted August 19, 2005 My picture is too large to load. e-mail me at rbracing11@msn.com and I'll send you a picture of a kit I build.Or here is a link to my website: http://groups.msn.com/RBRacingTwoStrokePor...hnicalinfo.msnw 406075[/snapback] Where did you get the squeeze bulb? How much did all that stuff cost? Quote Link to comment Share on other sites More sharing options...
banshee x Posted August 19, 2005 Author Report Share Posted August 19, 2005 (edited) i bought the following items from true value : 1 aceletiline gauge read 1psi to 30 psi $8.99- 2- 1 1\4" pvc male inserts w/ female 1\2" npt threaded inserts $.58 cents each 1- 1\2" npt to 1\8" npt bushing(metal) $2.98 1- 1/8" npt with valve stem $1.98 2- fernco rubber boots 1 1/2" both sides $3.98 each 2-1 1/2 inch pvc plugs $.65 each 1-6" piece of 3/4 pvc and a 90 degree elbow with a 3/4 slip to make accesing the gauge easyier abot $1.00 total (you will need pvc primer and cement to put this stuff together & thread sealant) i used an air compressor with a regulator on it set the regulator to 20 psi and filled the engine to 6psi attached is a picture total it cost about $23.00 with tax attached is a picture tighten the 2 1 1/4 pvc adapters to you intake manifold mine is for 35 mm carbs(yours maybe different take on of your manifold to the hardware store and make sure it fits and the attach the fernco rubber boot to the exhuast outlets make sure everything is tight,after you install spray the pieces you installed and make sure they're not leaking mine had to re-tightened hope this helps Edited August 19, 2005 by banshee x Quote Link to comment Share on other sites More sharing options...
banshee x Posted August 19, 2005 Author Report Share Posted August 19, 2005 a close up of the gauge Quote Link to comment Share on other sites More sharing options...
Machwon Posted August 19, 2005 Report Share Posted August 19, 2005 You can get a squeeze bulb from a hospital/home medical supply store (blood pressure bulb). They run in price range from $15-20 usually for a bulb. Otherwise you'll spend $25-30 to buy those parts and visit 3 different stores. I typically charge $40 for a 250r kit, $50 for banshee, all brand new parts. Quote Link to comment Share on other sites More sharing options...
2twin350s Posted August 20, 2005 Report Share Posted August 20, 2005 expandable rubber freezplugs work good to seal the exhaust ports. any auto store sells them for like2 bucks. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.