Banshee802 Posted December 30, 2018 Author Report Share Posted December 30, 2018 Too bad Payment Plan sold that motor Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted December 30, 2018 Report Share Posted December 30, 2018 Find a pipe as close to OD of the wrist pin slide it through both ends. Sent from my SAMSUNG-SM-G891A using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 30, 2018 Author Report Share Posted December 30, 2018 Find a pipe as close to OD of the wrist pin slide it through both ends. Sent from my SAMSUNG-SM-G891A using TapatalkNever would have thought of that! Thanks I’ll give it a whirlSent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 31, 2018 Author Report Share Posted December 31, 2018 Couldn’t find a pipe that would fit both. However I used a machinists square and checked for straightness along the middle portion of the case and small rod section of crank. Right side was flush, left side had a small gap. This confirms the left side top of the rod is tweaked to the right. My question is since it’s so minor would I have problems with just installing pistons and cylinders. Or would this small tweak turn the piston just enough to bind on the cylinder. I know this isn’t the correct way but havent seen a nice used crank for under $150Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
SKEETER Posted December 31, 2018 Report Share Posted December 31, 2018 It needs addressed. No point in doing more damage trying to cover up an issue, that isnt going away Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 31, 2018 Author Report Share Posted December 31, 2018 It needs addressed. No point in doing more damage trying to cover up an issue, that isnt going awayYeah I know lol. Just wanted to see what people would say to that. Definitely grabbing a new/used crank. New bored cylinders with pro x pistons are in the works aswellSent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 31, 2018 Author Report Share Posted December 31, 2018 Anyone have a good crank they want to sell me?Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
gusto Posted December 31, 2018 Report Share Posted December 31, 2018 Could it be cast this way? I would bring it to a machinist and get an opinion. 1 Quote Link to comment Share on other sites More sharing options...
gusto Posted December 31, 2018 Report Share Posted December 31, 2018 I don’t know where your at with money but if you need a crank hold off on the boring and do a 4 mil. You’ll be flying 1 Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 31, 2018 Author Report Share Posted December 31, 2018 I don’t know where your at with money but if you need a crank hold off on the boring and do a 4 mil. You’ll be flying This isn’t my main bike. This is just something I picked up since I saw a lot of potential in getting it running again. Plus I wanted the T6s it came with. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted December 31, 2018 Author Report Share Posted December 31, 2018 Could it be cast this way? I would bring it to a machinist and get an opinion. I don’t think it would be casted this way. Like locogato and some others said it could’ve been tweaked from hydro-locking. However I could bring it in to my work and have them look at it. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
gusto Posted December 31, 2018 Report Share Posted December 31, 2018 13 minutes ago, Banshee802 said: I don’t think it would be casted this way. Like locogato and some others said it could’ve been tweaked from hydro-locking. However I could bring it in to my work and have them look at it. Sent from my iPhone using Tapatalk All the hydro locked bikes that have been posted here are almost always bent in the middle where it’s weakest. Just seemed like a weird place to me. Was there damage to the piston by the wrist pin? I’d definitely take it to your work.. 1 Quote Link to comment Share on other sites More sharing options...
kawa110 Posted December 31, 2018 Report Share Posted December 31, 2018 I have a stock stroke welded crank I will sell you....With either all balls outer bearings or OEM. You’ll need to get bearings pressed on. Quote Link to comment Share on other sites More sharing options...
Banshee802 Posted January 1, 2019 Author Report Share Posted January 1, 2019 All the hydro locked bikes that have been posted here are almost always bent in the middle where it’s weakest. Just seemed like a weird place to me. Was there damage to the piston by the wrist pin? I’d definitely take it to your work..Not sure. Bought it this way with the cylinders and pistons off. Pistons got tossed before I got it. I have the cylinders but they are Chinese. The sleeves look runnable if I honed them but looks as if a kid beat the piss out of the edges with a hammer.Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
gusto Posted January 1, 2019 Report Share Posted January 1, 2019 I’d toss those cylinders right out. Farm and Sand Toys couldn’t even bore a set out because of the sleeves being pitted. I’ve read lots of reports on the casting flaws with them and sleeves not lining up. A set of used cylinders are 200 bucks. You might be pouring more money into this than you thought. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.