arena314 Posted September 6, 2018 Author Report Share Posted September 6, 2018 if I do this build then I'll be most likely be starting it after Thanksgiving due to the fact that the banshee runs flawlessly as of right now and I'd like to get 1 or 2 more rides in it this fall while the weather is nice although I have a few other quads theres something about the banshee that I like most. that gives me time to start piecing stuff together and buying it little by little so I'm not over whelmed by the cost. maybe I can also save a few bucks and buy the clutch basket first and waiting till after the build to get reedsSent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted September 6, 2018 Report Share Posted September 6, 2018 (edited) 2 minutes ago, arena314 said: if I do this build then I'll be most likely be starting it after Thanksgiving due to the fact that the banshee runs flawlessly as of right now and I'd like to get 1 or 2 more rides in it this fall while the weather is nice although I have a few other quads theres something about the banshee that I like most. that gives me time to start piecing stuff together and buying it little by little so I'm not over whelmed by the cost. maybe I can also save a few bucks and buy the clutch basket first and waiting till after the build to get reeds Sent from my SM-G965U using Tapatalk thats a good idea, buying it piece by piece might be better lol I like it that way thats what I did this past year it was easier than the year before where i dropped 2k at once i was like wtf after wards not to mention i did it on credit which is another wtf Edited September 6, 2018 by Ayesully810 Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 6, 2018 Author Report Share Posted September 6, 2018 lol not something I want to do that's for sure. so basically I'm looking at the cylinders, head, crank, clutch basket, clutch and all new seals everywhere. stock reeds will do for now I suppose Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
kawa110 Posted September 6, 2018 Report Share Posted September 6, 2018 ^^^yes to above....And Pancake bearing or ceramic clutch push rod ballModified shift starYou can get reeds, carbs, pipes, lockup in future. Quote Link to comment Share on other sites More sharing options...
kawa110 Posted September 6, 2018 Report Share Posted September 6, 2018 ^^^yes to above....And Pancake bearing or ceramic clutch push rod ballModified shift starYou can get reeds, carbs, pipes, lockup in future.Remove TORS if not done(cable and carb caps, idle screw kit) in plug TORS box. Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 6, 2018 Author Report Share Posted September 6, 2018 tors are removed I did that when I first got the quad and it has t5's on it which I think I'll run for the foreseeable future, stock reeds for now on and stock carbs also for the foreseeable future. most important stuff is the stuff you can only replace while your in the motor. where should I go to look for this shift star? any links you can send meSent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 7, 2018 Author Report Share Posted September 7, 2018 https://m.ebay.com/itm/Yamaha-Banshee-Modified-Shift-Star/142863467033?epid=1022894458&hash=item2143538219:g:R~sAAOSw7VRbRkY6is this one okay?Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
97Screamer Posted September 7, 2018 Report Share Posted September 7, 2018 36 minutes ago, arena314 said: https://m.ebay.com/itm/Yamaha-Banshee-Modified-Shift-Star/142863467033?epid=1022894458&hash=item2143538219:g:R~sAAOSw7VRbRkY6 is this one okay? Sent from my SM-G965U using Tapatalk Yes, MacDaddy does nice work. Any site sponsor (including MacDaddy) can get you setup and likely for a lower price than buying through eBay. In general be careful buying off eBay, if you don't know what's good and what's trash you can waste a lot of money buying trash. I also understand your desire to piece things together slowly but if you save up and buy it all at once from a sponsor you'll probably get a better deal then buying it all separate. Check out the sponsors here: https://www.bansheehq.com/bansheehq-sponsors/ Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 7, 2018 Author Report Share Posted September 7, 2018 anytime shopping on Ebay I make sure theres a brand I've heard of and is known for being good I just know that even "good" brands are better at making some products then others then I normally go to different sites looking at the same part to see who sells it for the lowest price. as far as the water pump going the stock impeller is good to run and just change the plastic gear to a billet correct? Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted September 7, 2018 Report Share Posted September 7, 2018 17 hours ago, arena314 said: anytime shopping on Ebay I make sure theres a brand I've heard of and is known for being good I just know that even "good" brands are better at making some products then others then I normally go to different sites looking at the same part to see who sells it for the lowest price. as far as the water pump going the stock impeller is good to run and just change the plastic gear to a billet correct? Sent from my SM-G965U using Tapatalk yes lots of ppl run the plastic impellar but the stock gear can be upgraded. mull sells good stuff and chariot. list of places i buy from -driveline, fast, macdaddy, Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 7, 2018 Author Report Share Posted September 7, 2018 thank you I purchased the water pump gear already. all the bearings in the transmission should I check them all and make sure there all good or should I pack them with grease before I put them back in?Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted September 7, 2018 Report Share Posted September 7, 2018 more than likely your 3 transmission bearings are fine just make sure they move good Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 7, 2018 Author Report Share Posted September 7, 2018 ok cool so I'll make sure all bearing like water pump impeller bearing and all that move good before reassembling. obviously new crank bearings and seals Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
arena314 Posted September 9, 2018 Author Report Share Posted September 9, 2018 hey guys another question.. what main and pilot jets would be a good safe starting point? I know I have a lot of time before I even start the project but I guess why not ask now. if I had the 4 mil crank, assassin top end that I posted the link to in my first post, t5 pipes, uni filter in stock air box, stock reeds for now, and +4 timing on the stock mikuni carbs with 23cc domes on pump gas. my elevation ranges from about 40 ft to 900 ft depending on where I rideSent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted September 9, 2018 Report Share Posted September 9, 2018 Toomey or Vito’s needle 32.5-37.5 pilots 340-360 mains needle in middle all motor are different but this is about where I was. 370 in cooler weather Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.