gusto Posted May 22, 2018 Report Share Posted May 22, 2018 Matt is a good guy Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 25, 2018 Report Share Posted May 25, 2018 Did you have any problems getting into silver lake with the shearers? Noise wise Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 25, 2018 Author Report Share Posted May 25, 2018 Nope, i didnt have any issues, and they were checking everyone for spark arrestors at the gate, i used sink screen in my silencers and they passed no problem. Didnt get tested for sound. Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 25, 2018 Report Share Posted May 25, 2018 Nice. I'm wanting to go but I have shearer too and been worried about driving 3 hrs and getting turned away Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 25, 2018 Author Report Share Posted May 25, 2018 2 minutes ago, Rippin'n'Runnin said: Nice. I'm wanting to go but I have shearer too and been worried about driving 3 hrs and getting turned away i wouldnt worry. i drive 3 hrs too never had an issue. u have a truck? you can always load your truck up and drive it into the dunes Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 26, 2018 Author Report Share Posted May 26, 2018 6 hours ago, Rippin'n'Runnin said: Nice. I'm wanting to go but I have shearer too and been worried about driving 3 hrs and getting turned away btw do you self a favor and DONT re use rivets in your end caps.. Just tap the silencer end cap and use some allen cap heads to bolt em back on. Easier to install and remove your "spark arrestor" that way. Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 26, 2018 Report Share Posted May 26, 2018 Appreciate the tip on the end caps. I do have a truck and heard that trick before. I would do that if i needed to. Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 29, 2018 Author Report Share Posted May 29, 2018 No problem good luck hmu if you make a trip there Pretty sure I got the jetting dialed in now with 50 pilot 2 turns out on the air screw CEL needle on 2nd clip 155 main. Have not chopped the main yet but I chopped a 150 when it was about 30 degrees cooler and it was lean so now its hot with a couple sizes bigger it should be pretty close. Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 31, 2018 Report Share Posted May 31, 2018 I will let you know. We are going end of June. Would definitely love to check out your bike sometime Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 31, 2018 Author Report Share Posted May 31, 2018 Sounds good you can come ride the finished project! Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
gusto Posted May 31, 2018 Report Share Posted May 31, 2018 Bike looks great. Do you have a DL slingshot on the clutch? IF so how much meat did you have to take off the screw tabs? Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 31, 2018 Author Report Share Posted May 31, 2018 Lane actually did the mod for me last year for the sling shot so idk, but what Lane said he did was, just grind the inside nubs all the way down flush to the cover and get screws that are just long enough to take up the threaded area. Then locktite them suckers in. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 31, 2018 Report Share Posted May 31, 2018 I've got a driveline lockup to go in my 421 when I build it this winter also. I might have to pick your brain a little when that time comes. Thanks for the invite on the ride that would be awesome. Have not ridden anything with that much power. I was up in gladwin last weekend and my stock cylinder dune port with shearers was walking all over my buddies yfz450. He couldn't shake me in the trails either which made me happy about my suspension mods last winter Quote Link to comment Share on other sites More sharing options...
Ayesully810 Posted May 31, 2018 Author Report Share Posted May 31, 2018 2 minutes ago, Rippin'n'Runnin said: I've got a driveline lockup to go in my 421 when I build it this winter also. I might have to pick your brain a little when that time comes. Thanks for the invite on the ride that would be awesome. Have not ridden anything with that much power. I was up in gladwin last weekend and my stock cylinder dune port with shearers was walking all over my buddies yfz450. He couldn't shake me in the trails either which made me happy about my suspension mods last winter oh sweet thats cool. Yeah 450s wont hang with ya haha suspension upgrade is big time needed for gladwin lots of whoops. Im actually headed up to my cabin in gladwin this saturday ill be doing a little riding. Quote Link to comment Share on other sites More sharing options...
Rippin'n'Runnin Posted May 31, 2018 Report Share Posted May 31, 2018 I'll have to let u know next time we go up there. Usually try to hit there a couple times a year. Don't get to ride as much as I like with job,wife,and kids. Gonna buy a blaster for my 10 year old son so he can start coming along soon Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.