ClaudeMachining Posted October 9, 2017 Author Report Share Posted October 9, 2017 Here is my buy list so far:Super Serval jugs, ported at Redline.Super cub head, domes setuped for AvGasCrankWorks 10 mill crank (is there other options?)Straight cut stock ratio gears.Pwk 39Roll design A-armsFox float Evol rc2LED pipes, because they are goergous.Hiper cf1, 4+1 front and 3+5 rear.Thats about it. I ride open road/trail most of the time. Did Cam built 521 with LED so far??Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote Link to comment Share on other sites More sharing options...
RagunCajun Posted October 9, 2017 Report Share Posted October 9, 2017 Yes but i dont think results were released. It was done for controls 521 build. Unless something changed, BBIF snipers made a little more up the face but it wasnt in my best interest to switch from my BBIF shearers. If you call redline up, he will tell you all about that and answer any question you have for the build. Quote Link to comment Share on other sites More sharing options...
ClaudeMachining Posted October 9, 2017 Author Report Share Posted October 9, 2017 Yes but i dont think results were released. It was done for controls 521 build. Unless something changed, BBIF snipers made a little more up the face but it wasnt in my best interest to switch from my BBIF shearers. If you call redline up, he will tell you all about that and answer any question you have for the build. I was not sure if Control was using LED. I'll go with LED even if they are not the best. Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted October 9, 2017 Report Share Posted October 9, 2017 Crankworks is the best billet out there in my opinion, I've just seen too many twister fail and only seen one CW fail. You could go forged but you said money isn't a concern so go billet for the extra 6 hundo. I would also go LED pipes even if they don't have the highest output,they just look incredibly awesome. If it was mine I would go 41 pwk they will give you more for up top wide open riding . Do the billet bowls that fast has now so you can get to the pilot n main rite through the drain plug. 1 Quote Link to comment Share on other sites More sharing options...
Deadbeat Posted October 9, 2017 Report Share Posted October 9, 2017 i see no mention alloy rod usage... 1 Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted October 9, 2017 Report Share Posted October 9, 2017 Does anyone know if CW new rods are being used yet . Last Time I inquired with them they were looking somewhere in Taiwan for production. Quote Link to comment Share on other sites More sharing options...
ClaudeMachining Posted October 9, 2017 Author Report Share Posted October 9, 2017 Crankworks is the best billet out there in my opinion, I've just seen too many twister fail and only seen one CW fail. You could go forged but you said money isn't a concern so go billet for the extra 6 hundo. I would also go LED pipes even if they don't have the highest output,they just look incredibly awesome. If it was mine I would go 41 pwk they will give you more for up top wide open riding . Do the billet bowls that fast has now so you can get to the pilot n main rite through the drain plug.I was kind of debating if i would try 35mm or go 39mm. 41 is big.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote Link to comment Share on other sites More sharing options...
SandSlingerOR Posted October 9, 2017 Report Share Posted October 9, 2017 This is exciting. Would love to see the numbers this puts down. Quote Link to comment Share on other sites More sharing options...
locogato11283 Posted October 9, 2017 Report Share Posted October 9, 2017 Some of the things you're debating about won't be an option Claude. Cam has certain things he will use/not use for a build like this. He will recommend 39 or 41PWK. The 35s won't be enough. He will be fine with LEDs. He will use Crankworks for the crank. Pretty much everything else you listed will be fine. Quote Link to comment Share on other sites More sharing options...
BANSHEE HP Posted October 9, 2017 Report Share Posted October 9, 2017 I see no mention on a "clue" on your list? Quote Link to comment Share on other sites More sharing options...
RagunCajun Posted October 9, 2017 Report Share Posted October 9, 2017 Yall are recommending carbs and other engine parts when the shop who's probably done the most 521 servals is doing it and probably has talked with him about it... Interesting. Quote Link to comment Share on other sites More sharing options...
ClaudeMachining Posted October 9, 2017 Author Report Share Posted October 9, 2017 It's just talk, i will follow what Cam will say.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote Link to comment Share on other sites More sharing options...
locogato11283 Posted October 9, 2017 Report Share Posted October 9, 2017 3 minutes ago, RagunCajun said: Yall are recommending carbs when the shop who's probably done the most 521 servals is doing it and probably has talked with him about it... Interesting. I'm not recommending anything. I am telling him Cam will either use 39s or 41s. Quote Link to comment Share on other sites More sharing options...
locogato11283 Posted October 9, 2017 Report Share Posted October 9, 2017 Just now, ClaudeMachining said: It's just talk, i will follow what Cam will say. Envoyé de mon SM-G935W8 en utilisant Tapatalk Have you talked to him? Quote Link to comment Share on other sites More sharing options...
ClaudeMachining Posted October 9, 2017 Author Report Share Posted October 9, 2017 I see no mention on a "clue" on your list? That's because i need more than one and it was obvious! ;-)Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.