Jump to content

421 Cub complete part out


Recommended Posts

Well, I am completely parting out my 421 Cub. I built it in late 2012-ish, broke in the engine, went to Glamis once then parked it for roughly 2.5 years. Life happened, just havent had the time to go riding and have gone into the deep end of track days and slippery slope of constantly throwing money at my car for better lap times. The bike sat out side, and certain parts show damage from sun and weather (rust) and have been priced accordingly. All prices are OBO, buyer pays shipping. Small parts that I have F/S, will be let go for the cost of shipping as indicated.

Since there is alot of stuff F/S, I will send more detailed pictures upon buyers request.

 

Engine - From what I remember, the engine ran flawless the last time I rode it 2+ years ago. A few weeks ago the bike would not turn over. A few days ago there was a lot of liquid in the right pipe. The cylinders will need replating due to the damage on the right cylinder. Rod bearings feel fine as well as the crank bearings. The top case has slight chain wack, but nothing major. Transmission operated as it should.

 

1-5 N down Dunable Override - 250
Crank Cases - 100
39mm Carbs setup for GAS w/ filters - 250
39mm billet manifold - 75
vf3 reeds - 125

 

 

Chassis parts - Frame is PC'd Trans Purple and lightened w/ bolt on subframe by Tim at Stellar. Bought the frame from Tim back in '09 and has not been wrecked. There is a spot of PC missing in the front of the frame. Frame is straight and titled, I would prefer local pickup but can ship at buyers expense via grey hound. The J-arms will need ALL ball joints replaced. The Direct Drive spindle mounts will need bearings replaced and need new valve stems. The tires are old, but dont show dry rotting and hold air. The swingarm has a crack behind linkage mounting point and discounted accordingly since it will need to be repaired, or will end up in the trash if nobody wants it.

 

Lightened frame w/ subframe and title; Frame is straight, a small area of pc missing in the front. I would prefer local pickup but can ship at buyers expense via grey hound- 500
Marvin Shaw13.5” rear Coilover - 175
Chrome Steering stem - 75
renthal handle bars - 40
chrome footpegs; rusted in certain areas - 50
polished linkage - 50


 

 

Sold list-

4mm crank

Billet clutch basket

lightened flywheel

timing plate

IGN coil

Stator Cover

Billet Dipstick

Marvin Shaw Front Hillshooters

Stellar J-arms

Brake pedal

Gear Slammer

+8 LSR swingarm

Billet rear brake cap

Parking brake block off

Water pump cover

Clutch lever

Kick starter

Chrome throttle assy

Spindle mounts

Rear Brake line

Shearer inframes

JJ&A Axle

421 cub cyl

chariot head w/ domes

Direct Drive lockout w/ clutch cover

 

 

Due to the holidays, I will not be able to ship as immediate as I have in the past.

 

 

IMG_0271_zpst0eguafv.jpgIMG_0270_zpseuheyova.jpgIMG_0269_zps7jiompgb.jpgIMG_0268_zps6fev7qn2.jpgIMG_0267_zpsu3felhyi.jpg

Edited by r/atvshee
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...