Dalton Posted October 7, 2015 Report Share Posted October 7, 2015 4mill Complete Top End Drag Ported Stock Cylinders, porting done by Alan Cain 66mm Blaster Pistons 19cc Race Gas Domes Compression Tested at 170PSI before pulled Low hours runs hard Bolt on and go No studs for head $450 Shipped Gifted payment or pay fees Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 7, 2015 Author Report Share Posted October 7, 2015 I have a correction to make.... the piston size is 66.25 Blaster pistons. I also want to disclose a very micro crack on the left cylinder only see picture No problems running this set up Quote Link to comment Share on other sites More sharing options...
mike0chek Posted October 7, 2015 Report Share Posted October 7, 2015 nasty spot for a crack, props for being honest for the sale 1 Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 8, 2015 Author Report Share Posted October 8, 2015 nasty spot for a crack, props for being honest for the sale Thanks Quote Link to comment Share on other sites More sharing options...
BANSHEE HP Posted October 8, 2015 Report Share Posted October 8, 2015 the crack I see wont affect anything. its just the aluminum casting. the steel sleeve behind it wont be cracked. 2 Quote Link to comment Share on other sites More sharing options...
n2otoofast4u Posted October 8, 2015 Report Share Posted October 8, 2015 That crack makes zero difference. Will have no effect. 1 Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 8, 2015 Author Report Share Posted October 8, 2015 That crack makes zero difference. Will have no effect. I agree. Just wanted to show it. 1 Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 8, 2015 Author Report Share Posted October 8, 2015 the crack I see wont affect anything. its just the aluminum casting. the steel sleeve behind it wont be cracked. I agree. Just wanted to show it. 1 Quote Link to comment Share on other sites More sharing options...
BANSHEE HP Posted October 8, 2015 Report Share Posted October 8, 2015 I understand, just wanted to make sure that other people dont get carried away on whether that cylinder is junk Bump for some good looking ported cylinders 1 Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 8, 2015 Author Report Share Posted October 8, 2015 I understand, just wanted to make sure that other people dont get carried away on whether that cylinder is junk Bump for some good looking ported cylinders Thanks again for pointing that out. These are excellent cylinders and a lot of work was put into them! 1 Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted October 10, 2015 Report Share Posted October 10, 2015 Glws those have a ton of work done, that's a 7-9 Hundo port job Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 10, 2015 Author Report Share Posted October 10, 2015 Glws those have a ton of work done, that's a 7-9 Hundo port job Yes a lot of work was done on these cylinders! They run hard! Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 13, 2015 Author Report Share Posted October 13, 2015 BUMP Offers?? Quote Link to comment Share on other sites More sharing options...
xbig pitax Posted October 14, 2015 Report Share Posted October 14, 2015 What base gasket is needed to run these and what are the exhaust and trans timing Quote Link to comment Share on other sites More sharing options...
Dalton Posted October 14, 2015 Author Report Share Posted October 14, 2015 What base gasket is needed to run these and what are the exhaust and trans timing Stock base gasket. No spacer plate. Ran with a 4mil crank. I don't know what the timing is. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.