RX-B Posted May 24, 2015 Report Share Posted May 24, 2015 Hello banshee HQ members. I'm new to post on this forum but have seen the great help everyone gives. I have a problem, my shee was working fine The bike was riding normal from when I unloaded it and all of a sudden the power and won't kick in. No mods have been done to the bike nor have I touched anything prior to the problem started. Has anyone experienced this. Help would be much appreciated thanks in advanced. Quote Link to comment Share on other sites More sharing options...
RX-B Posted May 24, 2015 Author Report Share Posted May 24, 2015 It is a 2010 banshee, no mods. I bought it 2 months ago first 2 stroke ever owned. Was riding around waiting for the other bikes to get ready so we can take off on bush trails. So it happened 10mins after having it on and working fine. Prior to that I noticed bit of fuel coming out of my carb over flow when fuel was off. Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted May 24, 2015 Report Share Posted May 24, 2015 did you mix the gas correctly? is the gas in the on position? do you have access to a compression tester? Quote Link to comment Share on other sites More sharing options...
Tommilicious Posted May 25, 2015 Report Share Posted May 25, 2015 Check the rubber tube between the two carbs is in place. Should go straight across from each carb to the other. I bought a "banshee that wont run right" from a guy on craigslist one time where that exact thing happened. Made the banshee run like crap with no power. Id next check spark plugs, followed by gas (use premium 93 or 91 octane at 32:1 mix - ethanol free if available) From there id check simple things like air filter/boots on carbs/ jets on carb/ fuel line etc Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
RX-B Posted May 25, 2015 Author Report Share Posted May 25, 2015 Fuel mixture is correct as I did it twice thinking that was the problem but it ain't but I will get all The other parts checked. Thanks Quote Link to comment Share on other sites More sharing options...
Larry's Shee Posted May 25, 2015 Report Share Posted May 25, 2015 Try unplugging Tors brain, left frame rail by gas tank, 3 wire plug. Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted May 25, 2015 Report Share Posted May 25, 2015 Have the carbs ever been off for a good cleaning? Quote Link to comment Share on other sites More sharing options...
RX-B Posted May 26, 2015 Author Report Share Posted May 26, 2015 (edited) ive only had the bike for 2 month and havnt pull nothing apart but will be taking off the carbs today. ill keep you updated. thanks. Edited May 26, 2015 by RX-B Quote Link to comment Share on other sites More sharing options...
Deadbeat Posted May 28, 2015 Report Share Posted May 28, 2015 Try unplugging Tors brain, left frame rail by gas tank, 3 wire plug. that^ before anything else Quote Link to comment Share on other sites More sharing options...
Larry's Shee Posted May 29, 2015 Report Share Posted May 29, 2015 ive only had the bike for 2 month and havnt pull nothing apart but will be taking off the carbs today. ill keep you updated. thanks. Do them one at a time as some parts are specific to that carb, but will fit on wrong carb, then will be trying to sort that mess out. Be sure you can see through main and pilot jet. Pull main jet holder/emulsion tube, little holes on side of it. Make sure air will blow through all passages. Set float height very important !! Write down main and pilot sizes, you/we will need to know later. While carbs are off, you are halfway to doing a leak test (hint) Quote Link to comment Share on other sites More sharing options...
RX-B Posted June 3, 2015 Author Report Share Posted June 3, 2015 Thanks everyone for the help. I pulled the carbs out gave them a good clean and bingo it's running good again. Quote Link to comment Share on other sites More sharing options...
Tommilicious Posted June 3, 2015 Report Share Posted June 3, 2015 Good to hear it was a simple fix. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
RX-B Posted June 3, 2015 Author Report Share Posted June 3, 2015 It's actually revving pretty high, I thought it was revving high to warm up but even after warming up it still revs high. Any ideas gents.... Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Tommilicious Posted June 3, 2015 Report Share Posted June 3, 2015 Turn your idle down? Left side of left carb Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
RX-B Posted June 4, 2015 Author Report Share Posted June 4, 2015 Thanks tommi all good now. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.