Geisick Posted February 9, 2015 Report Share Posted February 9, 2015 Selling a complete custom 16mm banshee engine. It has nothing but top of the line parts to make the most powerful and reliable combination possible. The entire engine is practically brand new as it was built with all new parts, crank, rods, clutch, pistons, bearings, seals etc… this last spring. It was dyno tuned and ridden one time last year, thus why I am putting it up for sale. 16mm billet Crankworks crank that has light weigh crank webs and is completely dynamically balanced to the weight of the pistons, then trued, and welded. 78mm Cheetah DM cylinders that are completely ported, and port matched with the cases, and comes with all the reeds, intakes, head o-rings, with two sets of custom cut domes (have two sets depending on elevation and fuel) Matton Billet Banshee cases ported, trenched and setup for the DM cylinders with the correct studs. Billet transmission gears that are fully micro polished and undercut. (undercut grears essentially will allow you to shift as fast as an override, but can also be ridden like a stock tranny without ruining the tranny or bending shift forks) Complete Hinson Billet Clutch setup: billet basket with springs (instead of cushions to hold up to the power), billet hub and billet pressure plate which allows for running and extra fiber. Direct Drive lockup clutch kit Direct Drive one piece reinforced clutch cover Direct Drive roller for pressure plate Straight cut gears Kick starter steel idler bushing Timing plate There is other stuff I can’t think of right now, and as stated you can see everything has been built with top end parts for strength and durability. There is also a lot of custom pieces and too many details to list. It is a great engine, but haven’t had enough time and have too many other projects. Selling this engine for half of what it would cost to duplicate. $7950 outright, or will knock $1000 off for a good banshee engine as a core. Best way to reach me is call 970-768-7168 (leave message if I don’t answer) or email me at geisickperformance@gmail.com Quote Link to comment Share on other sites More sharing options...
n2otoofast4u Posted February 9, 2015 Report Share Posted February 9, 2015 Who built this? What brand of gears in the tranny? Who did tranny work? Can you provide invoice from CW to verify the lightened wheels and balancing? What rod length? What brand and what ratio are the primaries? What did it make on the dyno? Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted February 10, 2015 Report Share Posted February 10, 2015 Stupid question, but who is currently balancing a banshee rotating assembly? Would like to have a TDR 10mm done with some 73mm pistons before I assemble it. Quote Link to comment Share on other sites More sharing options...
bluebanshee98 Posted February 10, 2015 Report Share Posted February 10, 2015 first post.... no feedback..... not all details given on motor.... too many details to list?..... for 7950 bucks you better give every little detail. there have been bigger dm motors going for less on this site done by some of the top builders. get all your shit together , pics, graphs numbers ect and report back. Quote Link to comment Share on other sites More sharing options...
BANSHEE HP Posted February 10, 2015 Report Share Posted February 10, 2015 Stupid question, but who is currently balancing a banshee rotating assembly? Would like to have a TDR 10mm done with some 73mm pistons before I assemble it. crank works Quote Link to comment Share on other sites More sharing options...
xbig pitax Posted February 10, 2015 Report Share Posted February 10, 2015 Pics! Want to see if this is worth jerking to lol Quote Link to comment Share on other sites More sharing options...
JCSO605 Posted February 10, 2015 Report Share Posted February 10, 2015 Beat it to billet ? Mmm yea I would. Quote Link to comment Share on other sites More sharing options...
Cwalker47 Posted June 21, 2016 Report Share Posted June 21, 2016 Will u take 6000$ Quote Link to comment Share on other sites More sharing options...
Bennett131 Posted June 22, 2016 Report Share Posted June 22, 2016 Will u take 6000$Post is over a year old Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.