Power_Man Posted September 28, 2014 Report Share Posted September 28, 2014 Let me start off this with telling back ground of this story. I was in a pretty bad accident on this machine last summer. Bent axles, rims, and few other parts. All replaceable items. So I replaced the stuff that I thought was hooped. Got used rims, axle. New bearing in carrier and new tires on the used rims. Started riding this summer after all repaired and I had a wobble in the tires/rims/axle. Well that's what I get for buying used (axle I assume). I bought a used durablue axle couple weeks ago, and just installed it. WOBLES STILL! It looks as if the whole axle is wobbling. Could anything in the carrier cause this, or did I get a bent axle? Video of it on stands. http://youtu.be/gDNLa45ElAk Quote Link to comment Share on other sites More sharing options...
Starwriter Posted September 28, 2014 Report Share Posted September 28, 2014 If I were you, I would take both axles to a machine shop and have them put them in the lathe between centers and run a dial indicator on them. Then you know for sure what you have. 1 Quote Link to comment Share on other sites More sharing options...
Power_Man Posted September 28, 2014 Author Report Share Posted September 28, 2014 Try this video instead. Shows the sprocket and disc brake wobble as well. But yes I think lathe is best bet to figure it out. http://youtu.be/7kuWT3KyP54 Quote Link to comment Share on other sites More sharing options...
n2otoofast4u Posted September 28, 2014 Report Share Posted September 28, 2014 Looks .030 out to me 1 Quote Link to comment Share on other sites More sharing options...
SAVAGE420 Posted September 28, 2014 Report Share Posted September 28, 2014 Quote Link to comment Share on other sites More sharing options...
Starwriter Posted September 28, 2014 Report Share Posted September 28, 2014 1 Quote Link to comment Share on other sites More sharing options...
SAVAGE420 Posted September 28, 2014 Report Share Posted September 28, 2014 HAHA thats awesome. Quote Link to comment Share on other sites More sharing options...
red96shee Posted September 28, 2014 Report Share Posted September 28, 2014 Yep about .030 out I would wait about 2 months then ask for your money back Quote Link to comment Share on other sites More sharing options...
Power_Man Posted September 28, 2014 Author Report Share Posted September 28, 2014 Yep about .030 out I would wait about 2 months then ask for your money back Why wait 2 months to ask for money back? I'm assuming your getting at something? Towards me or someone else? Quote Link to comment Share on other sites More sharing options...
Power_Man Posted September 28, 2014 Author Report Share Posted September 28, 2014 http://youtu.be/FFF4CoQ1qvg http://youtu.be/DdA34jquMK0 Quote Link to comment Share on other sites More sharing options...
Leadmonster Posted September 28, 2014 Report Share Posted September 28, 2014 Sucks Quote Link to comment Share on other sites More sharing options...
Starwriter Posted September 28, 2014 Report Share Posted September 28, 2014 That's not even close to the correct way to check it. It's probably still bent, but you should put it between centers. >=================================================< Quote Link to comment Share on other sites More sharing options...
Power_Man Posted September 28, 2014 Author Report Share Posted September 28, 2014 Well he is the guy that knows how to work the machine. Not me. I just watched. Seemed fine to me as the chuck grabs the axle where the bearing holds it then spins Quote Link to comment Share on other sites More sharing options...
Starwriter Posted September 28, 2014 Report Share Posted September 28, 2014 3 jaw chucks are not very accurate. They're for quickly setting up something short that you are going to machine all surfaces. I would find a new machine shop guy. I hope he didn't charge you for that little bit of useless information. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.