Dmx Posted May 29, 2014 Report Share Posted May 29, 2014 (edited) Let the pictures speak, max 15hours on topend and left side died. Is this usual when not using proper tool for wrist pin clip? I did double check and it was seated correctly during the top end assembly, but "kinda" looks like it wasnt hahahh. Edited May 29, 2014 by Dmx Quote Link to comment Share on other sites More sharing options...
Bennett131 Posted May 29, 2014 Report Share Posted May 29, 2014 holy shit that sucks haha ive never seen that before I always use picks of some sort and just make sure it stays put Quote Link to comment Share on other sites More sharing options...
Nieskes Posted May 29, 2014 Report Share Posted May 29, 2014 I use my fingers, i have never used a tool to put one in other then to seat it into the groove. Quote Link to comment Share on other sites More sharing options...
Dmx Posted May 29, 2014 Author Report Share Posted May 29, 2014 (edited) yep thats how ive done it before without problems, bare hands and little help with screwdriver- this just got me thinkin WTF...just have to blame the builder goddamnit. Edited May 29, 2014 by Dmx Quote Link to comment Share on other sites More sharing options...
hp2000 Posted May 29, 2014 Report Share Posted May 29, 2014 That's awesome !! Sent from my iPhone using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Banman1122 Posted May 29, 2014 Report Share Posted May 29, 2014 The open end of the clip should be a 180 from the notch in the piston or that can happen. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Dmx Posted May 30, 2014 Author Report Share Posted May 30, 2014 The open end of the clip should be a 180 from the notch in the piston or that can happen. Sent from my iPhone using Tapatalk Youve seen like this before? Maybe i put it somewhere around 160-170. Yes this is awesome, and sweeeeheeet! Time to go bigger. These cylinders are done, crank too. Skeeter you think banshee motor wrecks are common here in Finland? I have some doubts on that... Quote Link to comment Share on other sites More sharing options...
Dmx Posted May 30, 2014 Author Report Share Posted May 30, 2014 Yeah well this sucks cause i believed this topend had some shredding time left before next bore&pistons. Ive been thinking that crank will be 4mill and dune ported stock cylinders, better pipes&carbs for it also. Now i have t5`s and single carb, ss/sb dune ported. It depends what is available at the time i have the money. I think it would be bit cheaper and easier for me to have a whole bolt-on motor shipped here than collecting new/used parts here and there. Just have to get some money and start searching the next motor with pasi. Quote Link to comment Share on other sites More sharing options...
Deadbeat Posted May 30, 2014 Report Share Posted May 30, 2014 do you mean.........................................THIS Pasi^ Quote Link to comment Share on other sites More sharing options...
Dmx Posted May 30, 2014 Author Report Share Posted May 30, 2014 Haahhah! Hes the man. 1 Quote Link to comment Share on other sites More sharing options...
Pasi S. Posted May 30, 2014 Report Share Posted May 30, 2014 Thanks Dead! SKEETER, 4/6 of FI Banshees are down.. 1 Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted May 30, 2014 Report Share Posted May 30, 2014 Haha some good damage. Quote Link to comment Share on other sites More sharing options...
Banman1122 Posted May 30, 2014 Report Share Posted May 30, 2014 Yeah I had one come out but it didn't get to the rings and the wrist pin rubbed the wall. She didn't go kaboom tho. Lol Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.