#1JUANstunna Posted December 12, 2013 Report Share Posted December 12, 2013 I picked up all of the left over original stamps from Racers Edge which is now known as Dasa Racing.Stamps( two pieces ,top and bottom stamped out of .040 guage sheet metal on a 1 plane surface IE : flat from cylinder to stinger ) They then get welded together, then cut and twisted to mount on a Banshee. Flanges and stingers welded on as well as mounts and spring tabs. I'd like to see that done. Sounds pretty cool. Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 12, 2013 Report Share Posted December 12, 2013 Top And Bottom Racers edge Stamps Quote Link to comment Share on other sites More sharing options...
troyzstang Posted December 12, 2013 Author Report Share Posted December 12, 2013 So is it safe to assume that you are the same person that I spoke to last month? If so thanks again for your help identifying what I have. Also curious what a new set would cost? ( Small Bore / chrome) Troy Quote Link to comment Share on other sites More sharing options...
fappy'97 Posted December 12, 2013 Report Share Posted December 12, 2013 Those out of right pipes look great! Quote Link to comment Share on other sites More sharing options...
RobertR Posted December 12, 2013 Report Share Posted December 12, 2013 Could these be made into a in frame set??? Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 12, 2013 Report Share Posted December 12, 2013 Could these be made into a in frame set??? Got a sawzall and a welder ? lol Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 13, 2013 Report Share Posted December 13, 2013 They are $375 raw. I will have to check into a price on chrome. Quote Link to comment Share on other sites More sharing options...
Sandking Posted December 13, 2013 Report Share Posted December 13, 2013 What's you address and are you offering parts or just service. I'm local and don't like going to Trinity. Quote Link to comment Share on other sites More sharing options...
camatv Posted December 13, 2013 Report Share Posted December 13, 2013 if your building these with much better mounts that would be great. the biggest problem i have with mine is the junky ass mount setup.. IF you have a PV setup these pipes really scream. for 375 hell most track guys/ draggers should just grab up a set and try them.. also i take it you just have a set number of them? not a set of original die's? Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 14, 2013 Report Share Posted December 14, 2013 Ya I only have what's left over from the last run. If there was enough demand I could look into getting more made. Quote Link to comment Share on other sites More sharing options...
banshee760 Posted December 18, 2013 Report Share Posted December 18, 2013 Ya I only have what's left over from the last run. If there was enough demand I could look into getting more made. Just wondering because I haven't seen yet or heard mention any one saying if they or you make big bore racers edge pipes ? All I seem to hear is about the small bore version , and do you sell them ? Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 19, 2013 Report Share Posted December 19, 2013 There is a big bore flange 1.900 I.D. for these pipes However they are the same pipe and stamps, just bigger flanges. They will work good on everything up to 550 CC Personally anything bigger than that I would opt for a set of shearer big bores or some hand coned pipes set up for your motor. Quote Link to comment Share on other sites More sharing options...
Empire Industries Posted December 19, 2013 Report Share Posted December 19, 2013 Sorry I missed this post. I am in Riverside close to the 91 and Van Buren. I do service,repair,porting ,performance, parts and custom builds. Let me know how I can help. Email is the best way to get through to me. My Email is empireindustries01@gmail.com Thanks, Eric Quote Link to comment Share on other sites More sharing options...
camatv Posted January 17, 2014 Report Share Posted January 17, 2014 looks like you should keep running them through ebay. nice results! Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted September 16, 2014 Report Share Posted September 16, 2014 Bump for interesting. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.