DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 Thanks bro..... Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted September 4, 2013 Report Share Posted September 4, 2013 it does sound pretty flat man, what did the plugs look like ? Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 it does sound pretty flat man, what did the plugs look like ? Plugs looked good, nice tan color..... I have played with the jets, and still just cant get it going the way i want. I am looking into some new pipes.... Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted September 4, 2013 Report Share Posted September 4, 2013 sure the plate is at +4 and not -4 ? it also, kinda sounds like the clutch is slipping, or it just sounds really lazy. something is up, even with fmf's it should sound sharper. Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 sure the plate is at +4 and not -4 ? it also, kinda sounds like the clutch is slipping, or it just sounds really lazy. something is up, even with fmf's it should sound sharper. i am positive its at +4! . Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 Direct... Make an actual thread for your build... your barely getting any rev out of it. Have you swapped out electrical components? flywheel, cdi, coil, stator? have you tested / ohmed any of them??? if you have tried A LOT of different jetting combos... from rich to lean and it still wont rev out you got other issues rather then jetting. Fat jetting can cause what your experiencing vs lean will make it rev out but lack power. if you cant make it rev out.. start hitting electrical..... on a side note... whats the specs on your domes? squish? Hey Jess, Yea, i think i need to start a thread... I know there's gotta be something up. Only thing i have not swapped was electrical components. The domes were 25's cut by FAST. I have 043 Squish. I spend more time trying to tune this than ride...My wife says i'm addicted to the banshee... Thanks Gents/Gals Quote Link to comment Share on other sites More sharing options...
lms1977 Posted September 4, 2013 Report Share Posted September 4, 2013 sure the plate is at +4 and not -4 ? it also, kinda sounds like the clutch is slipping, or it just sounds really lazy. something is up, even with fmf's it should sound sharper. lol that's what I was gonna say. was it ported at all or completely as cast? it really sounds like a dog. with 320lb rider I could launch in 3rd with a 13 tooth sprocket sitting on the grab bar with my serval with these tires in the coal. Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 definitly get a threat going! do some basic stuff first!!! OHM test your plug caps, Ohm test stator, swap CDI's if you have a spare. Fresh plugs? proper fuel mixture? carbs synced? Floats set to spec? what kind of fuel do you run? how much cranking PSI does your motor have? Right now im getting 125 on both with the 25cc domes. I thought that was super low, but Jeff told me its good to go. Right now running R-50 32-1 with carbs synced with fast tool. Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 yea 25cc 125 seems low but its a safe PSI to say the least.. you def could use more compression but its a safe set up... so you are running just premium pump fuel.. NOT race fuel of any kind... if you are running race fuel your engine could be too weak to detonate the fuel which will rob MAJOR power and in turn do what your dealing with. so carbs seem in line otherwise. Carbs are good.. Absolutely no race fuel. 91Pump gas... Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 lol that's what I was gonna say. was it ported at all or completely as cast? it really sounds like a dog. with 320lb rider I could launch in 3rd with a 13 tooth sprocket sitting on the grab bar with my serval with these tires in the coal. Man, im 270...I guess i have no excuse anymore! Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted September 4, 2013 Report Share Posted September 4, 2013 Who set up your lock up? Quote Link to comment Share on other sites More sharing options...
DirectIntelect Posted September 4, 2013 Report Share Posted September 4, 2013 Who set up your lock up? I did, got it from Matoon.... Didn't play with the weights, i just threw it in there. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.