tylercaz99shee Posted July 26, 2013 Report Share Posted July 26, 2013 okay soo i traded an old set of tires for a blaster just for friends and gf to ride. you could tell it hadent ben ridden in a while soo i changed the crankcase fluid and drained gas and cleaned carb. now it smokes horribly, it doesnt smell good either i put amsiol dominator in it, and i run it in all my banshees and know what it should smell like. im thinking its the crank seal but dont want to tear into the engine if its something else, any ideas? Quote Link to comment Share on other sites More sharing options...
fappy'97 Posted July 26, 2013 Report Share Posted July 26, 2013 Oil is leaking passed the seal. JMO Quote Link to comment Share on other sites More sharing options...
Screamin Banshee92 Posted July 26, 2013 Report Share Posted July 26, 2013 Could be crank seal keep an eye on the level .. did u mix gas in tank cause I know the blasters had an oil injector system on them to? Quote Link to comment Share on other sites More sharing options...
tdod101 Posted July 26, 2013 Report Share Posted July 26, 2013 Could just be because it hasn't been started in a long time. Just need to clear all the crap out. Quote Link to comment Share on other sites More sharing options...
Starwriter Posted July 27, 2013 Report Share Posted July 27, 2013 Could be crank seal keep an eye on the level .. did u mix gas in tank cause I know the blasters had an oil injector system on them to? X2, yeah if the autolube pump is still hooked up and you premixed, you have too much oil going through. Most people remove the autolube pump. Highly unreliable and you don't know it's not working till your motor blows. The $10 billet Banshee ebay clutch cover vent block off fits the blaster perfectly when you remove the pump. http://www.ebay.com/itm/Banshee-Clutch-Cover-Vent-Block-off-Plate-/110747369144?pt=Motors_ATV_Parts_Accessories&hash=item19c90ebeb8&vxp=mtr Do a leakdown test to see if the crank seals are bad. The Blaster case splits vertically. They're not fun to get the trans all put back together. Not like a Banshee. The crank seals can be replaced without splitting the case. Again, not like a Banshee. Quote Link to comment Share on other sites More sharing options...
tylercaz99shee Posted July 27, 2013 Author Report Share Posted July 27, 2013 i know the autolube is took of im not sure if it was blocked of or just unhooked lol do you know what would happen if they just took the oil reservior off and pre mixed the gas? im pretty sure its burning case oil. idk im going to dive into it tomorrow and try and find out wats going on Quote Link to comment Share on other sites More sharing options...
Starwriter Posted July 27, 2013 Report Share Posted July 27, 2013 Make sure the line that went to from the pump to the carb is disconnected and capped at the carb. Although it probably wouldn't hurt anything for the pump to just spin gleefully, if it was me, I would completely remove it. Especially if you have to tear into the motor for crank seals. When you remove the pump, 1 part goes inward and 1 part goes outward. Don't remember exactly which. Just make sure you don't pound the wrong way and bust a hole in the clutch cover. Like I mentioned, do a leakdown test. You need a plate and a piece of innertube to block off the exhaust. Quote Link to comment Share on other sites More sharing options...
tylercaz99shee Posted July 27, 2013 Author Report Share Posted July 27, 2013 okay so the the crank seal was in backwards. the spring was facing outward. i am having a hell of a time trying to get that fucker out, and suggestions? Quote Link to comment Share on other sites More sharing options...
Deadbeat Posted July 27, 2013 Report Share Posted July 27, 2013 seal pick or a sharp screwdriver Quote Link to comment Share on other sites More sharing options...
tylercaz99shee Posted July 28, 2013 Author Report Share Posted July 28, 2013 i cannot get it out, i mean i tired everything, it wont even budge, im stumped. could it be because the guy before me put it in backwards? Quote Link to comment Share on other sites More sharing options...
Colby Posted July 28, 2013 Report Share Posted July 28, 2013 it will come out, may take a bit of elbow grease, and be careful not to gouge any metal surfaces around the area Quote Link to comment Share on other sites More sharing options...
Larry's Shee Posted July 28, 2013 Report Share Posted July 28, 2013 one or two drwall screws, plyers Quote Link to comment Share on other sites More sharing options...
tylercaz99shee Posted July 28, 2013 Author Report Share Posted July 28, 2013 the two drwall screws did the trick, now im just waiting for the new seals to come in Quote Link to comment Share on other sites More sharing options...
tylercaz99shee Posted August 1, 2013 Author Report Share Posted August 1, 2013 put the new seal in and fired here up, and its pouring just as much smoke as before, and its still buring gear oil!!! wtf i hate that damn little 12hp bike Quote Link to comment Share on other sites More sharing options...
Young Guns Racing Posted August 1, 2013 Report Share Posted August 1, 2013 If its burning gear oil thats probably also where the smoke and smell is coming from bud. If you have gear oil leaking into the crankcase it is being pushed thru the transfer ports and burned. Ur plug may show it to confirm this. Anyhow is thats ur issue, here comes the nightmare lol ur gonna have to pull the engine and split the crankcase Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.