BLOODRAGE Posted October 6, 2012 Report Share Posted October 6, 2012 just out of curiosity which one will produce more power,the superior sleeve stock stroke @76.5mm pistons or the 10mill @72.5mm. i just got the stock stroke back from a bore job and managed to get double ringed pistons so hopefully the compression goes up unlike the single ringed pistons. Quote Link to comment Share on other sites More sharing options...
BigRed350x Posted October 7, 2012 Report Share Posted October 7, 2012 Ill put my money on the 10mil being the better setup. Better torq curve with the bigger stroke. Jared Quote Link to comment Share on other sites More sharing options...
n2otoofast4u Posted October 7, 2012 Report Share Posted October 7, 2012 where do you find these relics? Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 7, 2012 Author Report Share Posted October 7, 2012 i bought the stock stroke off a guy on ebay,the 10mill off a member here. cant wait to put them both together,always keep a spare lol Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 7, 2012 Author Report Share Posted October 7, 2012 updated the pic,i think the 10mill needs to go visit mr bling,then one of the site sponcers for a bore job so i can get matching pistons Quote Link to comment Share on other sites More sharing options...
Dicklez Posted October 7, 2012 Report Share Posted October 7, 2012 Looks like a waffle iron. Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 7, 2012 Author Report Share Posted October 7, 2012 Looks like a waffle iron. yeah i got em from yo mamma's kitchen Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted October 7, 2012 Report Share Posted October 7, 2012 Looks like a waffle iron. Uhh, it's a panini press...... Jeez! Quote Link to comment Share on other sites More sharing options...
BigRed350x Posted October 8, 2012 Report Share Posted October 8, 2012 updated the pic,i think the 10mill needs to go visit mr bling,then one of the site sponcers for a bore job so i can get matching pistons Give Kevin @ HJR a call! He can bore your cyls and get you the right pistons for your crank/rod combo. -Jared Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 8, 2012 Author Report Share Posted October 8, 2012 Give Kevin @ HJR a call! He can bore your cyls and get you the right pistons for your crank/rod combo. -Jared kevin is doing the case trenching but i wont be able to do more till after the 19th.the 10mill is a project motor which is good for me Quote Link to comment Share on other sites More sharing options...
Paulie B Posted October 8, 2012 Report Share Posted October 8, 2012 10mil set-up all the way. It has a better balance of bore and stroke + the CC advantage. Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 8, 2012 Author Report Share Posted October 8, 2012 in that case the stock stroke might end up in the for trade section. never know Quote Link to comment Share on other sites More sharing options...
Paulie B Posted October 8, 2012 Report Share Posted October 8, 2012 They could be close though brother. Throw some top-end porting, 41mm carbs, top-end pipes, not alot of timing and not too much compression on the stock stroke set-up. Get it to turn up some rpms and hold together and it would make serious HP just not alot of usable torque. Quote Link to comment Share on other sites More sharing options...
BLOODRAGE Posted October 8, 2012 Author Report Share Posted October 8, 2012 only problem i had with the stock stroke it was a hog on gas. but after i got the new pistons charlie @ superior sleeve welded 2 lil holes on the pistons before they were open,my guess was i was losing raw gas through them causing the plugs to foul and the end on my exaust was always wet.so maybe itll be a lil easyer on plugs and gas now ill find out here soon.i need to pick up some cylinder base nuts,i lost em all from moving,sux big time but how do you port somthing thats already been drag ported? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.