Koba Posted July 15, 2012 Report Share Posted July 15, 2012 New to banshee's well atvs in general. Looking to make more power on my shee. I already have fatty pipes, bored 30 over, tors eliminator, and pods instead if intake. I got a buget of around 500 bucks right now. What should i be looking into? Quote Link to comment Share on other sites More sharing options...
Nightmare Posted July 15, 2012 Report Share Posted July 15, 2012 Port and polish and you should be happy Quote Link to comment Share on other sites More sharing options...
special06shee Posted July 15, 2012 Report Share Posted July 15, 2012 Port it, timing plate, head with proper domes!! Shee will rip!! Quote Link to comment Share on other sites More sharing options...
ticktock Posted July 15, 2012 Report Share Posted July 15, 2012 Call Brandon @ Wildcard Racing and tell him that. You will need gaskets, (rings depending on how old/compression), domes, head, port job.. Porting is going to be $350ish, gaskets $30, domes $80 and a Chariot head will run you $170 from Rootracing here on the Forums. Get a Chariot or NOSS head. They use all Prodesign domes and do not require a stud change. Best of luck and welcome to BHQ! Adam Quote Link to comment Share on other sites More sharing options...
BigRed350x Posted July 15, 2012 Report Share Posted July 15, 2012 I would invest in different pipes, then do a timing plate and a cool head. Sell the fatty's and if you have $ left over then look into porting. The fatty's are going to choke it down a lot compared to a good pipe. Quote Link to comment Share on other sites More sharing options...
thomas h. Posted July 16, 2012 Report Share Posted July 16, 2012 To stay in budget HJR port and mill the head should be about 400+ gaskets. Don't need domes and you could afford the timing plate. Your pipes are ok if you got some othe pipes else you may notice a little difference. Quote Link to comment Share on other sites More sharing options...
ticktock Posted July 16, 2012 Report Share Posted July 16, 2012 To stay in budget HJR port and mill the head should be about 400+ gaskets. Don't need domes and you could afford the timing plate. Your pipes are ok if you got some othe pipes else you may notice a little difference. Oh good point, get a Mull Engineering head instead of just having it milled. Adam Quote Link to comment Share on other sites More sharing options...
Koba Posted July 16, 2012 Author Report Share Posted July 16, 2012 (edited) What will tossing a cool head do for me? Edited July 16, 2012 by Koba Quote Link to comment Share on other sites More sharing options...
Colby Posted July 16, 2012 Report Share Posted July 16, 2012 What will tossing a cool head do for me? looks better.. cools better.. can change domes from pump/race gas very easily.. 21 cc domes will give you a good bottom end boost, and still run on pump fuel Quote Link to comment Share on other sites More sharing options...
Koba Posted July 16, 2012 Author Report Share Posted July 16, 2012 Ya i do mostly trail riding but i just did my first dune adventure which was great but i couldnt keep up with some four strokes. Stayed with my buddies suzuki 450r and built 400 till 4th i want to beat them badly haha. I deffinitly wanna do the cool head and probably a port job on my stock stuff for now. And probably some different pipes. Quote Link to comment Share on other sites More sharing options...
Koba Posted July 16, 2012 Author Report Share Posted July 16, 2012 Also i trail ride more often then hitting dunes so im not looking to go crazy like a drag set up yet Quote Link to comment Share on other sites More sharing options...
wr02 Posted July 16, 2012 Report Share Posted July 16, 2012 Call Brandon @ Wildcard Racing and tell him that. You will need gaskets, (rings depending on how old/compression), domes, head, port job.. Porting is going to be $350ish, gaskets $30, domes $80 and a Chariot head will run you $170 from Rootracing here on the Forums. Get a Chariot or NOSS head. They use all Prodesign domes and do not require a stud change. Best of luck and welcome to BHQ! Adam I agree with this. Brandon is a great guy and has worked on 3 of my bikes. He does an awesome job and can get you everything you need Quote Link to comment Share on other sites More sharing options...
mouzon30 Posted July 16, 2012 Report Share Posted July 16, 2012 its like this you want to beat the 450 you are going to need about 760 bucks call hjr and he will hook you up or one of the other guys but when you start porting and all the other mods its going to go from mild to wild Quote Link to comment Share on other sites More sharing options...
06specialedition Posted July 17, 2012 Report Share Posted July 17, 2012 I agree with this. Brandon is a great guy and has worked on 3 of my bikes. He does an awesome job and can get you everything you need Hit up Wildcard, your shee will RIP Quote Link to comment Share on other sites More sharing options...
dave5.0 Posted July 17, 2012 Report Share Posted July 17, 2012 Dude go four mill! You'll never look back! How come nobody said that yet? Wtf where's all the rednecks at? Haha Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.