gstaten24 Posted April 30, 2011 Report Share Posted April 30, 2011 Ok so I've searched a bunch of places and everywhere I find it, all it says is the proper gap. So my question is my gap was way off, how do I adjust it? I loosened the 2 Phillips heads and I can't move it forward enough to get the right gap. Any helP is appreciated!! Quote Link to comment Share on other sites More sharing options...
SAVAGE420 Posted April 30, 2011 Report Share Posted April 30, 2011 No need to undo the screws. Simply bend the tab in or out so that you get .018 with a feeler gauge or with the lid of a match box. Make sure the flywheel magnet it lined up when you bend and measure it. Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted April 30, 2011 Report Share Posted April 30, 2011 or round the hole with a dremel bit Quote Link to comment Share on other sites More sharing options...
Phelps Posted April 30, 2011 Report Share Posted April 30, 2011 why bend it? then it's not a true adjustment. loosen the screws and use a feeler gauge. Quote Link to comment Share on other sites More sharing options...
gstaten24 Posted April 30, 2011 Author Report Share Posted April 30, 2011 I might have to bend it cuz I have no way to round out the hole, just loosening the screws isn't enough it was really far out of whack Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted April 30, 2011 Report Share Posted April 30, 2011 check both pickup points too. Quote Link to comment Share on other sites More sharing options...
Jereme6655 Posted April 30, 2011 Report Share Posted April 30, 2011 check both pickup points too. andy's right.....when you loosen the 2nd one it can actually twist a little and cause the first screw to bind again......make sure they're BOTH loose.... Quote Link to comment Share on other sites More sharing options...
bansheesandrider Posted April 30, 2011 Report Share Posted April 30, 2011 I will ask it the second time, are you checking it on the trigger bumps on the flywheel? Quote Link to comment Share on other sites More sharing options...
gstaten24 Posted April 30, 2011 Author Report Share Posted April 30, 2011 Ok what I'm doing is turning te flywheel until the magnet pulls the little tab out then measuring it with my feeler gauge. Just to make sure I'm not having a brain fart the pickup coil is the little black piece on the outside of the flywheel towards the bottom right side correct? Quote Link to comment Share on other sites More sharing options...
fastquad02blaster Posted April 30, 2011 Report Share Posted April 30, 2011 Ok what I'm doing is turning te flywheel until the magnet pulls the little tab out then measuring it with my feeler gauge. Just to make sure I'm not having a brain fart the pickup coil is the little black piece on the outside of the flywheel towards the bottom right side correct? Yes. That is the pick-up. I used a buisness card between mine. Both lined up perfect. Make sure that you check them both. Quote Link to comment Share on other sites More sharing options...
thomas h. Posted May 1, 2011 Report Share Posted May 1, 2011 I installed a trinity timing plate and the closeest gap was .25 so i tokk a drill bit that fit inside the screw hole and milled (slotted) it alittle so the gap was perfect. only do the one hole the other side will pivot over giving you good gap. p.s. their was a good point to check both fly wheel nubs. min spec is .15 feeler gauges are cheap or you can mic the business card then use it for measurments mic = micrometer + harbor fright = 12.99 with 20% coupon Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.