SlowMoe Posted March 24, 2011 Report Share Posted March 24, 2011 Thanks for all the posts. Well the guy that said something about my pistons being installed right. Well they weren't. They were backwards. I bet this is what is causing my problems. I'll see tomorrow. I bet that's why no gas was getting to my plugs. I got to get new gaskets tomorrow and I'll test. I'm keeping my fingers crossed. Woohooo! i got one right! Quote Link to comment Share on other sites More sharing options...
88banshee Posted March 24, 2011 Report Share Posted March 24, 2011 Woohooo! i got one right! good job hey on the triple port thread do you want to cut down my pistns for free? ill run em in my sled see how it goes im willing to try it after all i have spare cylinders off of my 2nd parts sled Quote Link to comment Share on other sites More sharing options...
volcrano Posted March 24, 2011 Report Share Posted March 24, 2011 Thanks for all the posts. Well the guy that said something about my pistons being installed right. Well they weren't. They were backwards. I bet this is what is causing my problems. I'll see tomorrow. I bet that's why no gas was getting to my plugs. I got to get new gaskets tomorrow and I'll test. I'm keeping my fingers crossed. pfffft lol.mat what the hell!!!!epic failure!!!!!lol!get them fuckers switched.um,yes.that is the issue. Quote Link to comment Share on other sites More sharing options...
SlowMoe Posted March 24, 2011 Report Share Posted March 24, 2011 good job hey on the triple port thread do you want to cut down my pistns for free? ill run em in my sled see how it goes im willing to try it after all i have spare cylinders off of my 2nd parts sled You know I don't really know much about sled engines. I'd find out on a sled forum if people are cutting pistons on that particular engine. If it was my engine I'd go for it but I'd hate to cause someone else to jack up their stuff. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted March 24, 2011 Author Report Share Posted March 24, 2011 Just an update guys, she runs, I have some jetting issues to work out..its cuts out till you hit 4th or 5th gear then she pulls strong..i believe its the pilot. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted March 25, 2011 Author Report Share Posted March 25, 2011 well guys, I fixed my epic fail....Got the pistons swapped around, got it all back together..first kick she purred, and i revved it once, and i knew it was going to run right, it revved up fine...went down the road and it bogged a little down low i hit 4th and it started pulling hard...i went and got a 30 pilot, put it in and she runs good! I am pretty happy! Thanks a lot for mentioning that..i would have never even guessed thats what it could have been! Quote Link to comment Share on other sites More sharing options...
gotta_goatsfast Posted March 25, 2011 Report Share Posted March 25, 2011 Did you do a compression test and inspect the rings? The rings are now 180* from what they first started when they wore in to the cylinder. Quote Link to comment Share on other sites More sharing options...
volcrano Posted March 25, 2011 Report Share Posted March 25, 2011 interesting valid point.break her in mat,then check compression. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted March 25, 2011 Author Report Share Posted March 25, 2011 alright guys i will do a compression check when I break her in...its going to be cold for a few days so I probably wont be able to ride for a few days Quote Link to comment Share on other sites More sharing options...
AKheathen Posted March 25, 2011 Report Share Posted March 25, 2011 hey man, i was just wondering what happened to you. you still into the comp software repair? that stator doin good? Quote Link to comment Share on other sites More sharing options...
MatHolland Posted March 25, 2011 Author Report Share Posted March 25, 2011 hey man, i was just wondering what happened to you. you still into the comp software repair? that stator doin good? Well, its been sitting because i got tired of messing with it. I STILL haven't sent you that other one and im sorry. I know that you've sent me your address. Send me it again, and I can print a label off and send it to you. Yeah I still do repair...I grad. in july. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.