trickedcarbine Posted June 11, 2015 Report Share Posted June 11, 2015 Those $800 forged can take some abuse. 1 Quote Link to comment Share on other sites More sharing options...
camatv Posted June 11, 2015 Report Share Posted June 11, 2015 the more expensive 10 / 7 are a great choice. i dont know on the WSM or cheaper ones.. Quote Link to comment Share on other sites More sharing options...
mailman Posted June 12, 2015 Report Share Posted June 12, 2015 I can't find any negative press on the wsm cranks. Jet ski guys seem happy with them. I may roll the dice on the wsm one. For strictly scientific reasons of course. It's not like I am cheap or anything. Quote Link to comment Share on other sites More sharing options...
sprinklerman Posted June 12, 2015 Report Share Posted June 12, 2015 I can't find any negative press on the wsm cranks. Jet ski guys seem happy with them. I may roll the dice on the wsm one. For strictly scientific reasons of course. It's not like I am cheap or anything.I've heard good things about the wsm 7mm. Sent from my SM-G900R4 using Tapatalk Quote Link to comment Share on other sites More sharing options...
mailman Posted June 12, 2015 Report Share Posted June 12, 2015 Thx Sprinkleman. Quote Link to comment Share on other sites More sharing options...
sprinklerman Posted June 12, 2015 Report Share Posted June 12, 2015 Thx Sprinkleman.You're welcome. But that wasn't personal experience, just a trusted source. What I gathered from it was just run it a season check it, maybe run it another, then buy another kind of deal. They're cheap enough to do that and still be ahead money wise,,, vs a full blown crankworks. That was also putting good outer bearings on If I remember right. Sent from my SM-G900R4 using Tapatalk Quote Link to comment Share on other sites More sharing options...
xTHUNDERCATx Posted June 13, 2015 Author Report Share Posted June 13, 2015 (edited) I'll have to check with Brandon to see which one we ended up slapping in my bike but I'm pretty sure it was one of these 2. 10 mil with hot rods rods put on it. Its had 100+ gallons of alcohol ran through it and a destroyed piston. It was still holding when I found the welds on the crank broke. I'm going to send it off to have everything checked and maybe some new bearings put in, then its going back in. Edited June 13, 2015 by xTHUNDERCATx Quote Link to comment Share on other sites More sharing options...
dozer Posted June 15, 2015 Report Share Posted June 15, 2015 a few builders are taking the wsm apart, installing good bearings, true and weld, and they seem to hold up very well. Quote Link to comment Share on other sites More sharing options...
camatv Posted June 16, 2015 Report Share Posted June 16, 2015 wsm should just offer the webbs.. Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted June 16, 2015 Report Share Posted June 16, 2015 I wish Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted June 16, 2015 Report Share Posted June 16, 2015 Wsm uses the g-115 rod I've never personally seen one break but they are talked about like taboo on here . I use there jet ski and outboard stuff a lot and race pistons and I'm very pleased Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted June 16, 2015 Report Share Posted June 16, 2015 And I know the owner of a local wsm by , tdr cranks are wsm webs and it was also said that tdr had a hand In developing most of there two stroke, banshee shit 1 Quote Link to comment Share on other sites More sharing options...
locogato11283 Posted June 17, 2015 Report Share Posted June 17, 2015 TDR has been around a minute. Quote Link to comment Share on other sites More sharing options...
Whitbread Posted June 17, 2015 Report Share Posted June 17, 2015 TDR has been around a minute. Yup^. I'm going to guess he's almost double the age of most members here. I just talked to him this evening actually, he's going above and beyond to take care of my top end and definitely knows his shit. He's not particularly a drag race guy, but has probably forgotten more 2 stroke tech than many of us know. He has some WAY cool products in the works that will be a godsend to anyone making lots of HP. Quote Link to comment Share on other sites More sharing options...
Surfrjag Posted June 17, 2015 Report Share Posted June 17, 2015 What kind of products Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.