lt_ron Posted October 8, 2010 Report Share Posted October 8, 2010 Email me the pics and I will post them for you but all you have to do it down load it to photobucket than click on share and than get link codes find the img code and copy it and paste it over here my email is readsjr@gmail.com if you cant get it Quote Link to comment Share on other sites More sharing options...
banshee9090 Posted October 8, 2010 Author Report Share Posted October 8, 2010 (edited) Email me the pics and I will post them for you but all you have to do it down load it to photobucket than click on share and than get link codes find the img code and copy it and paste it over here my email is readsjr@gmail.com if you cant get it thanks for your kind and pleas ckeck your e-mail i already post them. Edited October 8, 2010 by banshee9090 Quote Link to comment Share on other sites More sharing options...
lt_ron Posted October 8, 2010 Report Share Posted October 8, 2010 Here yo go Quote Link to comment Share on other sites More sharing options...
superswire Posted October 8, 2010 Report Share Posted October 8, 2010 don't look too bad at all Quote Link to comment Share on other sites More sharing options...
James-26 Posted October 8, 2010 Report Share Posted October 8, 2010 Not to bad at all. Looks 1 million times better then the first picture posted. Quote Link to comment Share on other sites More sharing options...
Pasi S. Posted October 8, 2010 Report Share Posted October 8, 2010 You can take more out of it. Here is mine like it is right now. "round II" is still going... -Pasi S. Quote Link to comment Share on other sites More sharing options...
1bad450r Posted October 8, 2010 Report Share Posted October 8, 2010 hi every one this is my pic of porting job of my shee 4mil still in going. looks pretty good nice work Quote Link to comment Share on other sites More sharing options...
AKheathen Posted October 9, 2010 Report Share Posted October 9, 2010 looks decent. i would still spend some quality time cleaning up the transfers and detailing all the openings. make sure they all have a nice chamfer to them, and are symmetrical, too. Quote Link to comment Share on other sites More sharing options...
06specialedition Posted October 9, 2010 Report Share Posted October 9, 2010 looks decent. i would still spend some quality time cleaning up the transfers and detailing all the openings. make sure they all have a nice chamfer to them, and are symmetrical, too. X2.. But good job so far! Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted October 9, 2010 Report Share Posted October 9, 2010 and probably a hone / bore to clean up where you missed the hole. Quote Link to comment Share on other sites More sharing options...
banshee9090 Posted October 9, 2010 Author Report Share Posted October 9, 2010 (edited) well guys I appreciate all kind of help, suggestion and comment you have given me. I will tray to post final porting pic. as soon as I finish polishing it , I know that with the first cylinder I have no steady hands yet ! and I did some mistakes , the bottom of the transfer ports is down about 1.5 mm from piston dick bottom but the piston ring still hiding ,a couple of scratch existed on barrel of cylinder i hoop will not affect too mutch the compression ,I m not a shame because I m learning from my mistake, now I m porting second cylinder with steady hands and no mistakes show up. Edited October 9, 2010 by banshee9090 Quote Link to comment Share on other sites More sharing options...
AKheathen Posted October 9, 2010 Report Share Posted October 9, 2010 and probably a hone / bore to clean up where you missed the hole. i thought that was hair to find the hole, 'eh drew? Quote Link to comment Share on other sites More sharing options...
bad 350 shee Posted October 9, 2010 Report Share Posted October 9, 2010 what are the port durations?? Quote Link to comment Share on other sites More sharing options...
banshee9090 Posted October 9, 2010 Author Report Share Posted October 9, 2010 (edited) X2.. But good job so far! ya thanks Edited October 9, 2010 by banshee9090 Quote Link to comment Share on other sites More sharing options...
banshee9090 Posted October 9, 2010 Author Report Share Posted October 9, 2010 well guys I appreciate all kind of help, suggestion and comment you have given me. I will tray to post final porting pic. as soon as I finish polishing it , I know that with the first cylinder I have no steady hands yet ! and I did some mistakes , the bottom of the transfer ports is down about 1.5 mm from piston dick bottom but the piston ring still hiding ,a couple of scratch existed on barrel of cylinder i hoop will not affect too mutch the compression ,I m not a shame because I m learning from my mistake, now I m porting second cylinder with steady hands and no mistakes show up. i mean piston deck not dick sorry! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.