MatHolland Posted June 9, 2010 Author Report Share Posted June 9, 2010 the sticky on here well i had a slime guage, and my brass tip does not screw out? it will screw out from the bottom of the guage and theres a small looks like rubber hose and you pull it off, i cant get the brass piece off? do those plugs work fine? I had seen some complaints about them and others got rubber caps. Quote Link to comment Share on other sites More sharing options...
Jereme6655 Posted June 9, 2010 Report Share Posted June 9, 2010 a pilot jet being a size too small actually causes just one cylinder to act like crap....when i got my shee it was cuttin out hard on one of the cylinders...and around half throttle the other cylinder would come to life... turned out the pilot was the stock size and the instant i jumped it to a 27.5 the shee woke up....and no more bog Quote Link to comment Share on other sites More sharing options...
TNTS355 Posted June 9, 2010 Report Share Posted June 9, 2010 the sticky on here well i had a slime guage, and my brass tip does not screw out? it will screw out from the bottom of the guage and theres a small looks like rubber hose and you pull it off, i cant get the brass piece off? do those plugs work fine? I had seen some complaints about them and others got rubber caps. The brass piece stays on there. The aluminum nut I ground down to make it shorter. I drilled the end of the cap put the pressure gauage on and used silicone to seal it up. The air nipple, was a screw style (O'Reillys) that came in a two pack. The rubber freeze plugs have not been a problem, no leaks. I have held 6lbs in my motor for over 15 minutes, after I sealed up the leaks. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 9, 2010 Author Report Share Posted June 9, 2010 i got mine from o riellys just a single one...not sure what you are meaning..here is a picture of mine.. Quote Link to comment Share on other sites More sharing options...
TNTS355 Posted June 10, 2010 Report Share Posted June 10, 2010 i got mine from o riellys just a single one...not sure what you are meaning..here is a picture of mine.. take the rubber piece off of the guage that looks like a tire and the rubber piece out of the aluminum style nut. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 10, 2010 Author Report Share Posted June 10, 2010 then just drill a hole in the cap and use some of the glue? Quote Link to comment Share on other sites More sharing options...
TNTS355 Posted June 10, 2010 Report Share Posted June 10, 2010 then just drill a hole in the cap and use some of the glue? Use RTV or yama bond. on the bottom side of the cap put the tube nut on to help hold it in. You will need a threaded tire stem for the other cap. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 10, 2010 Author Report Share Posted June 10, 2010 ok lol thats what i thought just making sure, because my guage did look different..thanks for the specs on what size pvc i needed and freeze plugs. wasnt for sure on things so ended up not getting stuff today..i keep saying this haha but i really want to get it going again so i will for sure make a trip to murphys tomorrow. Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 10, 2010 Author Report Share Posted June 10, 2010 ok lol thats what i thought just making sure, because my guage did look different..thanks for the specs on what size pvc i needed and freeze plugs. wasnt for sure on things so ended up not getting stuff today..i keep saying this haha but i really want to get it going again so i will for sure make a trip to murphys tomorrow. Quote Link to comment Share on other sites More sharing options...
TNTS355 Posted June 10, 2010 Report Share Posted June 10, 2010 ok lol thats what i thought just making sure, because my guage did look different..thanks for the specs on what size pvc i needed and freeze plugs. wasnt for sure on things so ended up not getting stuff today..i keep saying this haha but i really want to get it going again so i will for sure make a trip to murphys tomorrow. Stock boots you will need: 1 inch pvc (you can make them what ever length you want them) 1 inch pvc caps pvc glue When I went to 34mm carbs I just added a 1 1/4 adapter for the larger boot. Quote Link to comment Share on other sites More sharing options...
mercury65 Posted June 10, 2010 Report Share Posted June 10, 2010 a pilot jet being a size too small actually causes just one cylinder to act like crap....when i got my shee it was cuttin out hard on one of the cylinders...and around half throttle the other cylinder would come to life... turned out the pilot was the stock size and the instant i jumped it to a 27.5 the shee woke up....and no more bog sound more like a pluged piot jet or pilot circut stock banshee with just pipes dont need bigger pilots but they do need the proper needle we are runing a ported 4mill on stock piolts but it also has the toomey needles Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 10, 2010 Author Report Share Posted June 10, 2010 I got all the supplies just a little bit ago and made one. I am going to wait until later on to do the test because its really hot outside, and i have some things that I need to get done. I will post my stuff here in a little bit. Quote Link to comment Share on other sites More sharing options...
SAVAGE420 Posted June 10, 2010 Report Share Posted June 10, 2010 I got all the supplies just a little bit ago and made one. I am going to wait until later on to do the test because its really hot outside, and i have some things that I need to get done. I will post my stuff here in a little bit. Come on now, first it was to loud last night, now its too hot out lol Quote Link to comment Share on other sites More sharing options...
MatHolland Posted June 11, 2010 Author Report Share Posted June 11, 2010 i know i know lol...well i did it..found a leak in the left intake boot. hoping that is my problem? i dont really understand how the left one can affect the right one tho lol Quote Link to comment Share on other sites More sharing options...
TNTS355 Posted June 11, 2010 Report Share Posted June 11, 2010 try it out and see if it works, I knew you had a leak Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.