kodie Posted March 16, 2009 Report Share Posted March 16, 2009 (edited) went riding today was runing fine. and then i noticed a loss of power took it back to truck and didn't have shit for compression on right side. so pulled head and juggs and this is what we found 4 mil, trail port, pro circuit pipes, 2 into 1 35 carb, +4 timing, chariot head with 22cc domes, 94 octane at 36:1, elevation 830 feet above damn those are shity pics let me see if i can get them bigger sorry hang on Edited March 16, 2009 by kodie Quote Link to comment Share on other sites More sharing options...
sheerider1026 Posted March 16, 2009 Report Share Posted March 16, 2009 those look like stock pistons to me.. how much time was on this topend???? sometimes they just go once the piston/cyinder fir gets loose.. its just hard to say.. time for a rebuild.. Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 defiantly not stock we just put these pistons in not more than 2 months ago just did the whole port/4 mil new pistons shit all at once 2 months ago or sooner. and i believe they are 60 over. Quote Link to comment Share on other sites More sharing options...
T_Shee Posted March 16, 2009 Report Share Posted March 16, 2009 which side was it that got trashed? proly a crank seal Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted March 16, 2009 Report Share Posted March 16, 2009 Damn! that looks like a lottal heat going on there, what do the tops of the rods look like? Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 right side...can't really see it too good but the left is fucked up a little around the rings. Quote Link to comment Share on other sites More sharing options...
278 Posted March 16, 2009 Report Share Posted March 16, 2009 Alot of things could have caused that... over heating, something getting into the motor, I think detonation will also cause that Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 Damn! that looks like a lottal heat going on there, what do the tops of the rods look like? dunno the bike is over at my buddies house where we work on them at. but ya we were sure it is heat related. just didn't know what it was that made them do it. Hoping someone could enlighten us. Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted March 16, 2009 Report Share Posted March 16, 2009 What is your jetting? Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 What is your jetting? i can't remember offhand ill have to check it out tomorrow to see. i want to say 205 but i can't member the other one Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 had him go check it for me 205 52 Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted March 16, 2009 Report Share Posted March 16, 2009 (edited) I am by no means a jetting expert but I have done it alot. 205 sounds WAY big to me given your mods and elevation. How did it run up top? Boggy? Also needle clip position is very important. I am sure someone with more experience than me will chime in and give you some insight. I really hope you didn't fry the tops of the rods! Edited March 16, 2009 by RUDEDAWG Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 205 to big for 1 carb? when i bought it from trinity it came with a 195 in it and a 198 and i think a 192. Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted March 16, 2009 Report Share Posted March 16, 2009 205 to big for 1 carb? when i bought it from trinity it came with a 195 in it and a 198 and i think a 192. OOPS! I didn't realize that you were a one lunger! My bad, but anyway, it looks like a jetting issue or improper break-in to me just my .02 Check out the jetting/exhaust forum, I think someone posted about what jets everyone is using on single carb set-ups. Quote Link to comment Share on other sites More sharing options...
kodie Posted March 16, 2009 Author Report Share Posted March 16, 2009 nah i broke her in good. you guys think running 94 instead of 100 or better octane helped fuck this shit up? my buddy thinks its the timing but a shit ton of people run +4 timing so i don't think it was timing. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.