BlasterKX Posted January 18, 2009 Author Report Share Posted January 18, 2009 the only way i can get it out is a tap extracter or drilling it out. what does a tap extractor do? Quote Link to comment Share on other sites More sharing options...
vulvafan537240 Posted January 18, 2009 Report Share Posted January 18, 2009 (edited) the only way i can get it out is a tap extracter or drilling it out. what does a tap extractor do? get a tap extractor. it has 2 fingers that insert into the flutes. be careful tho, they will break too if its in a big enough bind. heres a pic of one http://www.newmantools.com/walton/extrtap.htm Edited January 18, 2009 by volfan537240 Quote Link to comment Share on other sites More sharing options...
BlasterKX Posted January 18, 2009 Author Report Share Posted January 18, 2009 got it out and i was able to use the tap still. did the left side perfectly fine. going to go get the right side other carb from my buddy so il be able do that side. will post pics up in a lil bit Quote Link to comment Share on other sites More sharing options...
RollinRhino Posted January 19, 2009 Report Share Posted January 19, 2009 28s aren't that expensive if you find them used. They bolt right onto the stock boots. At least mine did but they are Mikunis. Not sure about the Keihins. I traded a set of steel wheels and BFG tires for mine. Quote Link to comment Share on other sites More sharing options...
BlasterKX Posted January 19, 2009 Author Report Share Posted January 19, 2009 i got everything on and working good. but it wont idle with the screws all the way in. i think i might need to get the slides up some more. how much of a gap should there bee at the bottom of the slides?? plus i think its gonna take awhile to tweak em back to normal with the thumb throttle adj. and the syning etc. Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted January 19, 2009 Report Share Posted January 19, 2009 i got everything on and working good. but it wont idle with the screws all the way in. i think i might need to get the slides up some more. how much of a gap should there bee at the bottom of the slides?? plus i think its gonna take awhile to tweak em back to normal with the thumb throttle adj. and the syning etc. If it doesn't idle with the idle screws screwed all the way in, you probably need to grind a little more off of the bosses so that the needles go into the main body further. Quote Link to comment Share on other sites More sharing options...
BlasterKX Posted January 19, 2009 Author Report Share Posted January 19, 2009 so prob take out alittle more and it should work ok then??? Quote Link to comment Share on other sites More sharing options...
RUDEDAWG Posted January 19, 2009 Report Share Posted January 19, 2009 so prob take out alittle more and it should work ok then??? I can't remember how much I had to grind off but, I am thinking 2mm.? Quote Link to comment Share on other sites More sharing options...
spurdy Posted January 19, 2009 Report Share Posted January 19, 2009 I can't remember how much I had to grind off but, I am thinking 2mm.? Damn! Who doesn't use lube when they tap? Aluminum is an alloy and should always have lube when tapped else it will guald. Lube is always better, ask your wife! Never tap dry, your just asking for issues. Best O Luck! SP Quote Link to comment Share on other sites More sharing options...
tony cub Posted January 19, 2009 Report Share Posted January 19, 2009 a while back i had two of my buddys bikes over to have the tores removed.on one i did it by the book with the idel screws and all as per the instructions.on the other set i didnt put in the idel screws(for a test).both bikes ideled the same and had the same throttle responce.the on that didnt have the screws was a hell of alot easier to adjust.so since then i dont screw around with the screws..just toss them in the trash.. Quote Link to comment Share on other sites More sharing options...
BlasterKX Posted January 19, 2009 Author Report Share Posted January 19, 2009 i took some more metal off and got em to idle damn near perfect. my one sides pilot circut isnt working all that great i just cleaned it but i need to take it all apart and do it. but it ran just like it did before i did this soooo i must be getting close. now i just need to do alittle bit more tweaking.lol Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.