Yamahopper10

Looking for the whole throttle assmebly, and cable if you have that too.

Who ported them?

Looking for set of stock stroke cylinders, ported or not. If you have pistons and a head even better. Let me know what you've got, and a price. Thanks

I want it. PM sent

Looking for a complete motor, or semi-complete motor, or bottom end, etc. Let me know what youve got. I have money ready to send for the right deal. I am in Eureka, Missouri. 63025. Figure out a price shipped and PM me. Thanks! Cody

Actually, no stator just cases, crank and trans. Also is the crank trued and welded?

How much for entire bottom end, including stator.

I have a set of very nice 12 paddle Extreme staggereds, triple buffed, on polished douglas 8x9 wheels. They are 22x11x8 72 ro, I will post pictures when I get home tonight. They have 5 rides on them, still have some nipples on the paddles. Price is 400+shipping. 636 575 5262

^ Exactly what he said. Put in in neutral so you dont burn your clutch out, and hold the throttle pretty much wide open 2-3 times (1 to 2 seconds each rev). You should hear and be able to feel the cylinders clean themselves out. Alcohol loads them up. If it doesnt clean out after 3-4 high revs then youre way rich, or could have other issues going on.

Ive looked up the t7's and cant find anything... Do you have a link to any info on them?

still have these?

Bike is sold!

Nobody interested at all? 3650 for everything!

I appreciate the offer but no thanks. Only trade I am interested in is a Seadoo RXP

thank you sir!, and the price is reduced to 3800!! this is a steal for whoever buys it. paddles and motor have 4 rides on them. those two together are well over the asking price!

I will take 3650 without the paddles.....

http://s1097.photobucket.com/albums/g350/Yamahopper10/?action=view&current=Banshee1.jpg 4 mill, trued and welded hotrod crank 115 mm rods , Fully ported cylinders by GT, 65.50 bore wiseco 795 series pistons,. 38mm mikunis setup for alcohol with billet bowls, i have gas needles and it can easily be switched back, pingel dual outlet, direct drive lockup clutch, 1-5 duneable override transmission, port matched case, billet intakes, vforce 3 reeds, lonestar +6 swingarm, whole motor is polished, CPI out of frames, smooth buff fronts, 12 paddle extreme staggerds on back. I had an 8 over swingarm on it, and had the intentions of switching it to gas, going to inframes and making it a duner...but I havent had time to ride lately, and probably wont have time at all this summer. The motor has under 5 hours on it, it was properly broken in with 3 heat cycles on gas. Runs very strong. I can send you to a link on youtube of me running it if interested. Price is 3950$, and im firm on it. I am located in Eureka, Missouri, about 30 miles west of st. louis. if you want more pictures, you may call or text me anytime 636 575 5262

Pipes are gone.

350$ + shipping ... My bad for no price on the pipes, and for not replying right away, Ive been extremely busy.

I have a set of CPI oof small bores for sale. They are chrome, and in good condition. No major scratches or dings. Here is a link to a pic of them, for some reason im dumb and cant get my files below 50k. If you have any questions, or you are interested shoot me a message on here, or text me at 636 575 5262 Thanks, Cody http://s1097.photobucket.com/albums/g350/Yamahopper10/Banshee/?action=view&current=Banshee1.jpg

also, sounds like your pilot jet(s) is clogged

This may sound dumb, but make sure the little hose is in place that connects the two carbs.

Have a set of chrome CPI small bore out of frames.

swingarm is sold

Sold!