Jump to content

r/atvshee

Members
  • Posts

    1,164
  • Joined

  • Last visited

1 Follower

About r/atvshee

  • Birthday 07/14/1991

Contact Methods

  • AIM
    bigballnpimp91

Profile Information

  • Gender
    Male
  • Location
    New River, Az

r/atvshee's Achievements

HQ Soldier

HQ Soldier (2/5)

2

Reputation

  1. Yes I still have it.
  2. No, spindle mounts are sold
  3. Swingarm, water pump cover and clutch lever are SOLDSOLDSOLD
  4. Clutch basket, impeller, brake pedal, gear slammer, brake cap, block off, dip stick, stator cover, kicker, front shaws, throttle assy are SOLDSOLDSOLD Shearers and axle are SALE PENDING
  5. Crank, flywheel, timing plate and IGN coil are SOLD
  6. Inbox cleared and PM's replied
  7. Well, I am completely parting out my 421 Cub. I built it in late 2012-ish, broke in the engine, went to Glamis once then parked it for roughly 2.5 years. Life happened, just havent had the time to go riding and have gone into the deep end of track days and slippery slope of constantly throwing money at my car for better lap times. The bike sat out side, and certain parts show damage from sun and weather (rust) and have been priced accordingly. All prices are OBO, buyer pays shipping. Small parts that I have F/S, will be let go for the cost of shipping as indicated. Since there is alot of stuff F/S, I will send more detailed pictures upon buyers request. Engine - From what I remember, the engine ran flawless the last time I rode it 2+ years ago. A few weeks ago the bike would not turn over. A few days ago there was a lot of liquid in the right pipe. The cylinders will need replating due to the damage on the right cylinder. Rod bearings feel fine as well as the crank bearings. The top case has slight chain wack, but nothing major. Transmission operated as it should. 1-5 N down Dunable Override - 250 Crank Cases - 100 39mm Carbs setup for GAS w/ filters - 250 39mm billet manifold - 75 vf3 reeds - 125 Chassis parts - Frame is PC'd Trans Purple and lightened w/ bolt on subframe by Tim at Stellar. Bought the frame from Tim back in '09 and has not been wrecked. There is a spot of PC missing in the front of the frame. Frame is straight and titled, I would prefer local pickup but can ship at buyers expense via grey hound. The J-arms will need ALL ball joints replaced. The Direct Drive spindle mounts will need bearings replaced and need new valve stems. The tires are old, but dont show dry rotting and hold air. The swingarm has a crack behind linkage mounting point and discounted accordingly since it will need to be repaired, or will end up in the trash if nobody wants it. Lightened frame w/ subframe and title; Frame is straight, a small area of pc missing in the front. I would prefer local pickup but can ship at buyers expense via grey hound- 500 Marvin Shaw13.5” rear Coilover - 175 Chrome Steering stem - 75 renthal handle bars - 40 chrome footpegs; rusted in certain areas - 50 polished linkage - 50 Sold list- 4mm crank Billet clutch basket lightened flywheel timing plate IGN coil Stator Cover Billet Dipstick Marvin Shaw Front Hillshooters Stellar J-arms Brake pedal Gear Slammer +8 LSR swingarm Billet rear brake cap Parking brake block off Water pump cover Clutch lever Kick starter Chrome throttle assy Spindle mounts Rear Brake line Shearer inframes JJ&A Axle 421 cub cyl chariot head w/ domes Direct Drive lockout w/ clutch cover Due to the holidays, I will not be able to ship as immediate as I have in the past.
  8. 22x11x8 14 paddle extreme 72" RO - 410 shipped. Still in very good condition. No leaks or dry rotting. Cascade chrome "race position" foot peg and billet shifter. 120 shipped Chrome is still in good condition. Due to the foot pegs having a different position than stock, I will not separate shifter from pegs. Also, I wouldnt recommend these for any one that rides in decent sized whoops, unless you dont mind digging your feet through the sand. Will also trade for chrome stock pegs or billet pegs with billet or chrome shifter.
  9. Domes are sold! Open to offers on both rear Shaws!
  10. Paddles are sold! I'm open to offers on everything else
  11. 13.5" Rear Marvin Shaw Hill Shooter - $180 shipped No leaks, setup for a +12 swingarm with linkage 13.5" Marvin Shaw Rear Competition - $150 shipped No leaks, setup for +6 Swingarm with linkage
  12. Sale pending on it. Will let you know if anything happens if your still interested.
×
×
  • Create New...