FASTOYS

Ok all, please pm me prices and pics if have . I dont so much care about chain wacks but NO oil leaks, and NO worn areas where crank bearings go. Also need good studs/threads and gasket surfaces. Thanks!

In need of a good set of Banshee engine cases.....watcha got?

Pics?? Please send them to me . Gasket surfaces good and all threads good??

Yeah no doubt, 24hour straight through drive each way. Ughh We have been busy as he** so a few days off for rest will be nice. As far as i know we are camping back in wash 3 with Marvin Shaw aka Yarnell Specialties. I will have duct tape on my flag pole so others will know im an HQ Member and hopefully stop and say hey. I will take your # down and try to holler at ya. Should be there late THursday. GOT SAND??? ha I know right?! You just have to say you know what..... heck yeah lets do this, and if you get enough guys going its not bad at all. We will pee Okbeast in the sand and Roost over it for ya though. :biggrin: Hows that for service? :tongue: :beer: On a side note , hope your ok down there with all the tornadoes that just ripped through yesterday. Im gonna dig Glamis weather as its Sleeting/freezing rain here. yuk.

Just a heads up. See you boys when we get back as i need a couple of days off and Duner 440, Jeepman 380, Rippen, and myself are going to Glamis for the Pres. day and HQ raffle...

Need to know your elevation. A cool head, and timing plate will really wake it up. Also may consider gearing it too.

Grimm, Most all the prices you need are on our site, Give me a ring this morning around 9 am central or anytime after as i will be in the shop. BumpaDz28, i didnt forget you as i have many callbacks to make this morning and you are one of them. I was busier than a cat coverin shit on concrete Sat..

Usually seen on Motorcycles and it keeps sticks, rocks, and brush from getting between frame and brake lever and bending it out..

I always recommend riding easy for the first 10-15 miunutes so everything can seat in and you can make sure your adjustment is correct.

Glad that took care of it. 160lbs and 4 degrees timing will run fine on Prem 91-93 fuel IF jetted correctly.

When im not working 8 days a week on 4 wheelers (click F.A.S.T. link below), im a person skilled in distinguishing the qualities by the taste of my favorite Chinese all you choke down your neck buffet. :laugh:

http://www.farmandsandtoys.com/partdetail.asp?partid=281 These will help , ask CSML on here.

Check your compression, lower your needles back where they were first, then richen more only if needed, richen your air screw 1/2 turn, and i cant imagine with an airbox it needing more than 320s when cold temps. Always shake/mix your gas/oil mix good especially when that cold. Your problem is JETTING.

I carry the 4mm cut domes if i can help give me a hollar.

You may loose a tad of bottom end but will have alot harder HIT in the mid and top. Should be at least 1-2 bikes faster in a race.

z28 I have ridden at both places you ride at and know what it takes to make power at your altitude. Do your research and you will be happy with porting. Seems alot of people are getting porting from others and not getting the bottom end they want. ANyone can make top end power, so discuss with whomever is doing your work and make sure to get what YOU want/need.

Really?? I just looked and theirs are $82 and ours are $70 .

Bang for the buck the 421 Cub is hard to beat. I have a 10mm Cub as im a heavier rider and needed the torque. We have done 421s that will definetly hang or beat 10mms or bigger. A 10mm will be about $800-1,000 MORE to build than the 4mm and the gain is only about 8-10hp. Either way over stock this will be a fun build and wild ride!

We ship em to Canada all the time also , usually takes less than a week.

Should be a NICE Billet kicker on that thing as it shows delivered yesterday. Im sending the new Shockwears out tomorrow JB so that should make it pop even more. Looks real good!!

WOW, nobody recommended LUBING the cable. Even new cables come dry!

Remarks like that first one ..... Thats ONE, Roost from my Raptor coming your way. I hope all the HQers do follow through with the duct tape idea. Mine is still on the flag (about 3 ft up on pole) from the HQ ride at Oklahoma. But only a few people actually did it there. :sad: 10mm .....stock stroke ...hell there all 350s. :ninja:

I would of gladly swapped you out if you had bought them from us. As mentioned might try to call who you bought them from. Like in my sig says: "You can go broke saving money". We all learn the hard way sometimes.

Thanks for the order Killshee, you should have them in 2-3 days.

50 DEEP ??? Hell that would be the Jersey/New York guys alone from the sounds of it. lol Really looking forward to some 80s and Cali. sunshine as it is -1 windchill here this morning. Ok , So do the HQ guys want to put Duct tape 1/2 way up on thier flag pole so we know who the HQ guys are ????