junkyarddog Posted March 19, 2014 Report Share Posted March 19, 2014 Here's my info 2001 banshee Just installed new hot rod crank stock stroke New top end wiseco pro light 65.50mm Stock 26mm carbs Stock intake's Air box no lid Toomey T-5 exhaust 650 elevation Trinity stage IV porting 13-41 sprockets Bike will be a dunner/aggressive trail/ play on pump gas 91oct here Any advice would be sweet just looking for a ball park this is a new build and I need to order a jet kit but I have never ran any of the Trinity Porting stuff and still not sure on the dome size I need to run with the setup the duration is 188 on the cylinders and software says 24cc domes will run 138 psi And 23cc domes will be 145psi Hell I was thinking around 20cc with the porting any ideals Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 I know that's right but this is a buddy's bike were putting togather and he had theses cylinders laying around and we just had bored and are going to use them its a buget thing Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 188 is what Jim at passion racing said he done the bore job for me theses cylinders came off a flat track quad and had 17cc domes running race fuel if that helps any to get a idel on the porting Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 20-21's is what I was thinking untill jim at passion threw that curve ball at me and said 23-24's hell that's a stock head Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 Don't know he was in a hurry so he could of been off a few Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 That's what I got from passion lol Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 Fing trinity crap and K&T dident port theses at least there not stamped like others iv had Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 19, 2014 Author Report Share Posted March 19, 2014 I got a set of 22's I'm thinking when parts come in ill slap them in and check compression and go from there Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 Need ideals here I put 22cc domes in to test compression to se where I'm at and it made 100psi wtf right so now I'm thinking I need to go buy some 20's maby 19's?? Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 I dident check seeing its all stock stroke and cylinders now if it was a high compression reading I could adjust it to less with base gasket but i dont think there's a way to adjust to make less squish is there Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 I'm going back to get the 22 domes and put back in a check it I had passion bore the cylinders and there good also the ring end gap was spot on at 10thou so now I'm heading to a buddy's house to pick the 22's again and check squish easy pezy Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 The gasket kit was a K&S? Maby there to thick ill know as soon as I get the squish check Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 I'm thinking it might be thicker but don't know Well I checked squish with a pice of sod I have here that's .062 and piston don't even hit it so now I'm going to the auto parts house and gona get a little thicker sod so I guess I might be looking at new base gaskets after I measure what I got now? Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted March 25, 2014 Author Report Share Posted March 25, 2014 Ok average was 58-60 so ? Tear down and check thinness I guess never checked I'm running the kit off eBay that came with hit rod crank and wiseco 65.50mm pistons and gaskets wtf!! Needs to be done by Tommorow Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.